---
title: "Bubble Level – Free Online Spirit Level for Your Phone"
description: "Use your phone as a bubble level (spirit level). Lay it on a shelf or hold it to a frame and see the tilt in degrees, percent or inches per foot. No app."
url: https://devicetests.com/bubble-level
language: en
---

# Bubble level

Turn your phone into a spirit level for shelves, frames and furniture.

> **Interactive test.** This test runs in the browser on the user's own device and uses that device's hardware, so an AI agent can't run it for the user. To use it, the user opens <https://devicetests.com/bubble-level> in a browser.
>
> **What it needs:** A phone or tablet with motion sensors (computers have none). The user taps Start bubble level (and Allow on iPhone or iPad) and lays the device on a surface or stands it on an edge, in their own browser, which shows the tilt in degrees, percent, inches per foot or mm per metre, with two-spot calibration and Hold reading.
>
> **Cost:** Free. Nothing to install and no account.

Your sensor readings stay on your device. We don't record or upload them.

This bubble level needs JavaScript to read your phone's tilt. Turn on JavaScript, or open this page in a current Chrome, Safari, Samsung Internet or Firefox on your phone.

## Quick start

1. Open this page on your phone or tablet.
2. Press **Start bubble level**. On an iPhone or iPad, tap **Allow**.
3. Lay the phone on the surface, or hold its edge against it.
4. Lower the side it says is higher, until it says **Level**.

## How to read your results

The level works in two ways. It picks the right one from how you hold the phone.

| How you hold the phone | What you see | What it measures |
| - | - | - |
| **Lying on its back** | A round level with a bubble | The tilt in every direction: **Side to side** and **Top to bottom** |
| **Standing on an edge** | A long level, like a spirit level | The tilt along the edge it stands on |

The bubble always moves to the **higher** side, as in a real spirit level. The words under it say how far off level it is, and which side is higher. At 0.2° or less, it says **Level**.

> **Tip:** To hang a picture, hold the phone’s long edge against the top of the frame. Turn the frame until the level says **Level**.

### Degrees, percent or inches per foot

Choose how to show the tilt under **Show the tilt in**, below the buttons. The page remembers your choice. In full screen, the choice is hidden: press **Exit full screen** to change it.

| Unit | Good for | Example |
| - | - | - |
| **Degrees** | Pictures, shelves, furniture, appliances | 0.5° is a small tilt you can just see |
| **Percent** | Patios, paths, ramps, gardens | 2% = 2 cm of rise over 1 metre |
| **Inches per foot** | Drain pipes, gutters, decks | ¼ inch per foot is a common fall for a drain pipe |
| **mm per metre** | Floors, tiling, worktops | 3 mm/m is a small slope |

A wheelchair ramp of 1 in 12 is 8.3%, or 4.8°. Always check your local building rules for the slope you need.

### Hold reading

In a tight spot, like behind a washing machine or on a high shelf, you can’t see the screen. Put the phone down, press **Hold reading** and let go. After a moment the number freezes. Then pick up the phone to read it. Press **Show live reading** to go on.

### Calibrate for the best reading

Press **Calibrate**, then follow the steps:

1. Lay the phone on a flat surface and press **Mark first spot**.
2. Turn the phone round, top where the bottom was, on the same spot.
3. Press **Mark second spot**.

The level now knows your phone’s own error, and leaves it out. It also tells you how much the surface itself was tilted. The surface doesn’t need to be level for this to work.

## If something’s wrong

These are the most common fixes, easiest first.

### Nothing happens, or “No motion sensors found”

1. Open this page on your phone or tablet. Computers have no tilt sensor.
2. On an iPhone or iPad, press **Start bubble level**, then tap **Allow**.
3. If you tapped **Cancel** on an iPhone, close the browser fully and open this page again.
4. In Chrome on Android, tap the icon left of the address, then **Permissions**. Turn on **Motion sensors**.

### It says tilted on a table you know is flat

A case with a bump, or a camera that sticks out, tilts the phone. Take off the case, or press **Calibrate** and follow the steps. Calibration only works with the phone lying on its back.

### The numbers keep moving

Small changes of 0.1° are normal. Put the phone on a firm surface and let go of it. On a soft surface, like a bed or a carpet, the phone sinks unevenly.

### It switches between the round and the long level

The level changes when the phone tilts more than about 45°. Lay the phone flat for the round level, or stand it fully on its edge for the long one.

### The screen turns while the phone stands on an edge

That’s fine. The long level always lies along the edge the phone stands on, even with the rotation lock on.

### The screen turns off

The page asks your phone to keep the screen on while the level runs. Some phones in battery saver ignore this. Turn off battery saver, or tap the screen now and then.

## How this test works

Your browser shares the phone’s tilt with web pages, about 60 times a second. The page works out how far the screen is from level in each direction. The bubble moves the full way to the rim at 10° of tilt.

Calibration takes the middle of two readings, turned 180° apart. The surface’s tilt changes sign between them, and the phone’s own error doesn’t, so the middle is the phone’s error. Corrections over 5° are refused. That much comes from a very uneven case or a phone that moved, not from the sensor.

Slope units come from the angle: percent is the rise over 100 units of length, and inches per foot is the rise over 12 inches.

To check what each motion sensor does, use the [gyroscope test](https://devicetests.com/gyroscope-test). See [how we test phones and computers](https://devicetests.com/how-we-test#phones-and-computers) for where our limits come from.

**What the level can see**

- The tilt, shown to a tenth of a degree, lying flat or on an edge.
- Your phone’s own error, after calibration.

**What it can’t see**

- The sensor’s factory accuracy. Browsers smooth the readings first.
- Whether the edge of your phone is straight. Most are rounded, so lay it on the flattest side.

[How we test our tools](https://devicetests.com/how-we-test)

## Questions and answers

**How accurate is a phone level?**

A phone's tilt sensor is usually right to within a few tenths of a degree. That is good enough for pictures, shelves, furniture and appliances.

A bump on the case or a camera that sticks out can tilt the phone more than that. Press **Calibrate** once, or take off the case. For building work, use a real spirit level. Measuring lengths is a different job: see [how accurate iPhone Measure is](https://devicetests.com/how-accurate-is-iphone-measure).

**Is a bubble level the same as a spirit level?**

Yes. Both names mean a level with a bubble in a glass tube of liquid. This page draws the same thing, and the bubble moves to the higher side in the same way.

**Why does nothing happen on my computer?**

Computers have no tilt sensor, so there is nothing to read. Open this page on your phone or tablet. Some 2-in-1 laptops and Windows tablets do have one and work here.

**Where is the level on my iPhone?**

In the Measure app, in the Utilities folder. Can't find it? See [where the Utilities folder is](https://devicetests.com/where-is-the-utilities-folder-on-iphone). Open Measure and tap **Level**. Then hold the iPhone against the object. It turns green when the object is level.

The Camera has a small level too, for straight photos. Open Settings, tap Camera, and turn on **Grid** and **Level**.

**My phone already has a level. Why use this one?**

Use whichever is quicker for you. The iPhone level is inside the Measure app. Many Android phones have none. This page also shows the slope in percent or inches per foot, holds a reading, and tells you which side is higher.

**What do percent and inches per foot mean?**

They say how much a surface rises over a length. 2% means 2 cm of rise over 1 metre. ¼ inch per foot means a quarter of an inch of rise over each foot of length. Both are about 1.2°.

**Does this site record how I tilt my phone?**

No. The readings are only used on this page while it is open. If you calibrate, or choose a unit, that small setting is kept in your browser for next time.

## Related tests

- [Online ruler](https://devicetests.com/online-ruler): A ruler in cm, mm and inches at real size on your screen, once you set it with a bank card.
- [Gyroscope test](https://devicetests.com/gyroscope-test): Check your phone’s gyroscope, accelerometer and compass, with a bubble level.
- [Online compass](https://devicetests.com/compass): Find north and which way you face, with your phone’s compass.
- [Touch screen test](https://devicetests.com/touch-screen-test): Find spots on your touch screen that don't respond, count fingers and catch ghost touches.
- [GPS test](https://devicetests.com/gps-test): See how accurately your phone or computer finds where you are, and how far it wanders.
