---
title: "USB Hub or Dock Keeps Disconnecting? Find the Cause | DeviceTests"
description: "Webcam freezes, keyboard drops out, everything goes at once? Compare three setups to tell power, a port, the cable, the hub and power saving apart, then fix it."
url: https://devicetests.com/usb-hub-disconnecting
language: en
---

# USB Hub or Dock Keeps Disconnecting? How to Find the Cause

By Jacob Hicks · Published November 6, 2026

Short answer

Most drops through a hub or dock come from **too little power**, **a worn cable or port**, or **a power-saving setting** that turns the device off. To find which, plug the device that drops **straight into the computer**, then into **the hub with nothing else on it**, then into **the hub with everything on it**. Where the drops start tells you the cause.

What drops?

- [One device: the webcam, the keyboard, the mouse](https://devicetests.com/usb-hub-disconnecting#step-2-compare-three-setups): Compare three setups for it
- [Everything on the hub at once](https://devicetests.com/usb-hub-disconnecting#the-hub-or-dock-itself): Look at what they share: the hub, its cable, its power
- [Only the screen on a dock](https://devicetests.com/second-monitor-not-detected#5-docks-and-displaylink-adapters): See the monitor guide
- [A wireless mouse or keyboard](https://devicetests.com/usb-hub-disconnecting#wireless-receivers-on-a-hub): Its receiver may be too close to USB 3
- [A new accessory on a Mac laptop never connects](https://devicetests.com/usb-hub-disconnecting#a-mac-laptop-wont-use-a-new-accessory): The Mac may not allow it yet

_The same webcam connected to a laptop three ways. Top: a cable straight from the laptop to the webcam. Middle: through a small hub with nothing else on it. Bottom: through the same hub, which also has a keyboard and a drive on it_

1. Straight into the computer. Drops here too: it isn’t the hub.
2. Through the hub, with nothing else on it. Drops start here: the hub, its cable or its port.
3. Through the hub with everything on it. Drops start only here: too much on the hub at once.
4. The device that drops. Our test for it shows when it stops.

Change one thing at a time, and use each setup for as long as the drops usually take to show.

## Step 1: catch the drop in our test

Open the test for the device that drops in its own browser window, and keep that window where you can see it. When the device stops working, the test shows it. It can’t tell you why: that is what the setups in step 2 are for.

### Webcam

Test it now

Webcam test

Choose your USB camera in the **Camera** list. If it drops, the test says **Your camera stopped** or **The picture stopped**.

[Open the webcam test](https://devicetests.com/webcam-test)

### Keyboard

Test it now

Keyboard tester

Click the keyboard picture first, then type a few keys now and then. Keys that stop lighting up mean the keyboard wasn’t reaching the computer.

[Open the keyboard tester](https://devicetests.com/keyboard-tester)

### Mouse

Test it now

Mouse test

Click and scroll in the box now and then. If the pointer freezes and clicks stop showing, the mouse dropped.

[Open the mouse test](https://devicetests.com/mouse-test)

### Microphone or headset

Test it now

Mic test

Choose your USB microphone or headset in the test. Talk now and then. If the meter stops and the test says the microphone stopped, it dropped.

[Open the microphone test](https://devicetests.com/mic-test)

### Controller

Test it now

Controller tester

Press a button first. If the controller disappears from the test, it was disconnected.

[Open the controller tester](https://devicetests.com/controller-tester)

![The webcam test while it runs. A warning over the picture says: The picture stopped. The camera may be unplugged, or another app took it. On the right, What we see says The picture stopped](https://devicetests.com/_astro/webcam-test-picture-stopped.BVU5I_98_1VpyWC.webp)

When pictures stop coming from the camera, our webcam test says so. Here we stopped a simulated camera's picture.

After a drop, plug the device back in if needed and press **Try again** in the test. The camera and microphone tests stop when you switch to another tab or minimise their window, so keep that window in view.

**What a browser can’t tell you:** our tests show when a device stops. They can’t measure how much power a hub gives, or test a cable. A USB drive or a hub has no test in the browser: watch whether the drive disappears from File Explorer or Finder.

## Step 2: compare three setups

Use one device that drops, the one you notice first. Keep its test open.

> Save your files first
>
> Before you unplug the hub, finish copying files and eject any USB drive on it. Unplugging a drive while it copies can damage the files on it.

1. **Straight in.** Unplug the hub. Plug the device into a port on the computer itself. Use it as you normally do. Leave out anything in between too: a monitor’s USB ports, a keyboard’s port, an extension cable or a KVM switch.
2. **The hub, alone.** Plug the hub back in, with only that device on it. On a dock, keep its power and the screen connected, and unplug the other USB devices. If the hub has a power adapter, plug that in too. If that alone stops the drops, it was the power.
3. **The hub, with everything.** Add your other devices one at a time. Note which one you added when the drops start.
4. **Another port on the hub.** If it dropped on the hub, move it to another port of the hub, with the same devices on the hub as before.
5. **Another cable or computer port for the hub.** Plug the hub into another port of the computer, or use another cable between them. On a desktop computer, try a port on the back.

> Give each setup time
>
> If the drops come every hour, use each setup for an hour. A setup that worked for five minutes doesn’t prove much.

Note what happened in each setup here. The sheet points to the likely cause and the next setup to try. Add more devices if several drop. Your answers stay while this browser tab is open, also when you open one of our tests and come back.

The same rules, as a table:

| What you saw | Most likely cause |
| - | - |
| It drops straight into the computer too | The device, or that port of the computer. Two devices doing this: the computer |
| Another cable or computer port for the hub fixed it | That cable or port |
| One port of the hub drops it, another doesn’t | That port of the hub |
| Fine straight in, drops on the hub with nothing else on it | The hub, its cable or its power |
| Other devices are fine alone on the hub, this one drops | This device on this hub: it may need more power |
| Fine alone on the hub, drops with everything on it | Too much on the hub at once |
| Drops after it sits unused, or after sleep | A power-saving setting |
| Drops only on battery | Too little power: keep the laptop on its charger |

## Too much on the hub

Every device on a hub shares the hub’s power and its link to the computer. Where that power comes from depends on the hub. A **bus-powered** hub has no power adapter: it takes all its power from the computer’s port.

_Two hubs, each with a webcam, a drive and a mouse. Top: the hub's only cable goes to the laptop, whose port is marked. Bottom: the same hub also has a power adapter plugged into a wall socket, which is marked_

1. The computer’s port. On a bus-powered hub, it powers everything.
2. A bus-powered hub: no power adapter of its own.
3. Every device takes a share. External hard drives are among the hungriest.
4. A hub’s own power adapter. Now the devices get their power from the wall.
5. A dock with its own adapter can also charge the laptop, through the same cable.

A hub without its own power adapter shares out what one port of the computer gives.

- Up to this for one device on a USB 2.0 port: 2.5 watts (USB 2.0 specification)

  500 mA

- Up to this for one device on a USB 3 port: 4.5 watts (USB 3.2 specification)

  900 mA

- The most a USB-C port can offer at 5 volts, if it offers it: 15 watts (Microsoft)

  3 A

- All the USB 2.0 rules promise each port of a bus-powered hub

  100 mA

mA (milliamps) and A (amps) measure electric current: how much electricity flows. A bus-powered hub splits one port’s current between all its devices. When it runs out, “any USB device attached to the computer may suddenly disconnect”, says the hub maker Plugable.

Docks with their own adapter have a limit too. Microsoft’s Surface Thunderbolt 4 Dock, for example, gives 7.5 watts on each USB-A port and 15 watts on each USB-C port, with 67.5 watts for all of them together.

1. **Plug in the hub’s power adapter**, if it has one. Apple and Microsoft both say to check that the hub has power.
2. **Keep a laptop on its charger.** Microsoft’s advice for USB devices that need more power is not to run on battery.
3. **Unplug the devices you don’t use.** Microsoft suggests this too.
4. **Move the hungriest devices** to the computer’s own ports: hard drives, and phones or anything else that charges.
5. **Use a hub with its own power adapter** if you need everything on one hub.

### Windows

**USB device might need more power** (on Windows 10: **USB device might not be working properly**). Windows says your PC “might not provide enough power” to the device. Plug the device into its own power if it has one, run the laptop on its charger and unplug devices you don’t use.

### Mac

**USB Devices Disabled**, or a message that the device needs more power. Apple’s steps: unplug the device and plug it back in, try another port, plug it straight into the Mac instead of the hub, and plug a hub with its own power adapter into the wall.

## A worn cable or port

A loose plug or a worn cable makes devices drop when you touch the desk or move the laptop.

1. **Wiggle the plug gently** while our test runs. If the device drops, that plug, cable or port is worn.
2. **Try another cable** between the hub and the computer, if the cable comes off the hub. Use the cable that came with the dock, as Microsoft suggests. A USB-C cable that fits isn’t always good enough: it must carry the same speed and charging power as the dock’s own.
3. **Try another port** of the computer, and another port of the hub.

## The hub or dock itself

If a device drops on the hub even with nothing else on it, but not straight in, look at the hub.

1. **Restart it.** Eject any drives on it first. Unplug the cable to the computer and the hub’s power. Wait 30 seconds. Plug in the power first, then the cable to the computer. Plugable and Dell both give this order. Some docks have their own reset steps in their manual.
2. **Update the dock.** Dell asks you to update the computer’s BIOS (its startup software) and drivers, and the dock’s own drivers and firmware (the software inside the dock). Microsoft’s Surface docks get firmware through Windows Update.
3. **Plug the hub straight into the computer,** not into a monitor, a keyboard or another hub, while you test. Every extra hub adds cables and ports to rule out. Two hubs without their own adapters share one port’s power.
4. **Watch the charger.** Some docks and monitors with a charging port briefly cut their USB ports when the charger goes in or out. Plugable describes this for one of its monitors. Eject drives before you change the charger.
5. **Try the dock on another computer**, if you can. If it drops there too with one device on it, the dock is the likely fault.
6. **Replace it** if it still drops with one device on it, after another cable and another port.

> Where to find dock updates
>
> Search the maker’s support site for your dock’s model name and “firmware”. The model is on the label under the dock.

**DisplayLink docks:** USB devices on the dock’s ports don’t go through its DisplayLink chip, says DisplayLink. So its software only matters when the dock’s screens drop: see [docks and DisplayLink adapters](https://devicetests.com/second-monitor-not-detected#5-docks-and-displaylink-adapters).

## Windows turns USB devices off to save power

A device that drops after it sits unused, or after sleep, may be turned off by Windows to save power. Microsoft recommends leaving this power saving on. So turn it off only as a test, and turn it back on if the drops don’t stop.

1. Right-click **Start** and choose **Device Manager**.
2. Open **Universal Serial Bus controllers**.
3. Right-click **USB Root Hub** or **Generic USB Hub** and choose **Properties**.
4. On the **Power Management** tab, clear **Allow the computer to turn off this device to save power**. Choose **OK**.
5. Do the same for the other hubs in the list, and write down which ones you changed. Some have no **Power Management** tab: skip those.

If the drops don’t stop after a day or two, tick the same boxes again.

## A Mac laptop won’t use a new accessory

A Mac laptop with Apple silicon (an M1 chip or later) asks before a new USB accessory may connect. Choose **Allow**. If you chose **Don’t Allow**, the accessory can still charge, but the Mac won’t use it. Unplug it and plug it back in: the Mac asks again.

1. Choose **Apple menu** **System Settings** **Privacy & Security**.
2. Scroll down and click **Accessories**.
3. Next to **Allow accessories to connect**, choose **Ask for new accessories** (the usual choice) or **Automatically allow when unlocked**.

Unlock the Mac before you allow an accessory. A Mac that has been locked for three days or more may need unlocking before a known accessory works again.

## Wireless receivers on a hub

A small receiver (dongle) for a mouse or keyboard can lose its signal next to USB 3. Intel found that a USB 3 drive disturbs the 2.4 GHz radio band nearby, even when it is only plugged in. In Intel’s test, moving the receiver away on a USB 2 extension cable fixed it. Plugable says the same about busy USB 3 ports.

1. **Put the receiver on a USB 2 port**, away from busy USB 3 ports, if the computer has one.
2. **Or use a short extension cable** to bring the receiver closer to the mouse or keyboard, away from the hub and drives.

More on wireless links in [Bluetooth vs 2.4 GHz](https://devicetests.com/bluetooth-vs-2-4-ghz#make-the-wireless-link-you-have-faster).

## It drops even straight in

Then the hub isn’t to blame. Try another port of the computer first. Then follow the guide for your device: [keyboard](https://devicetests.com/keyboard-not-working#2-check-the-connection), [mouse](https://devicetests.com/mouse-not-working#the-mouse-is-dead), [webcam](https://devicetests.com/laptop-camera-not-working) or [microphone](https://devicetests.com/microphone-not-working). To find out whether it’s the device or the computer, use [the swap test](https://devicetests.com/device-computer-or-app).

## When it comes and goes

1. **Keep our test open** in its own window, where you can see it.
2. **Note the time and what was happening** when it dropped: a call started, the laptop woke up, a drive was copying, the charger went in.
3. **Use each setup for as long** as the drops usually take to show.

## Questions people ask

**Why do all my devices disconnect at the same time?**

They share the hub’s link to the computer. When several devices drop together, look at what they share: the hub, its cable, its power or the computer’s port.

**Is a powered USB hub better?**

For hard drives, or many devices at once, yes. Its devices get their power from its adapter, not from one port of the computer.

**Can I plug a hub into a hub?**

It can work, but test without it. Two hubs without their own adapters share one port’s power, and every extra hub adds cables and ports that can fail.

**Why does my wireless mouse stop when I plug in a drive?**

A USB 3 drive can disturb the receiver’s radio when the two sit close together. Move the receiver away on a short extension cable.

**Why does my hub stop working after sleep?**

Windows may turn the hub or its devices off to save power. Unplug the hub and plug it back in. If it happens often, try the power-saving steps above.

**Can a website test my hub or cable?**

No. A browser can’t measure power or test a cable. It can show when a device stops, which is what you need to compare the setups.

## Sources

- [Microsoft: Fix USB-C problems in Windows (USB device might need more power; connect directly to the PC)](https://support.microsoft.com/en-us/windows/fix-usb-c-problems-in-windows-f4e0e529-74f5-cdae-3194-43743f30eed2)
- [Microsoft: Mouse and keyboard problems in Windows (make sure the hub has power, or plug in directly)](https://support.microsoft.com/en-us/windows/hardware/input-devices/mouse-and-keyboard-problems-in-windows)
- [Apple: If you see USB Devices Disabled on your Mac (another port, no hub, power the hub)](https://support.apple.com/en-us/102204)
- [Apple: Allow USB and other accessories to connect to your Mac (Mac laptops with Apple silicon)](https://support.apple.com/en-us/102282)
- [Microsoft Learn: USB Type-C manual tests (Power Management tab, Allow the computer to turn off this device to save power)](https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/type)
- [Microsoft Learn: USB selective suspend (on by default; Microsoft recommends not turning it off)](https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-selective-suspend)
- [Microsoft Learn: USB Type-C on Windows, FAQ (up to 5 V at 3 A, 15 W; up to 100 W with Power Delivery)](https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/faq--usb-type-c-connector-on-a-windows-system)
- [Microsoft Learn: Surface Thunderbolt 4 Dock (7.5 W USB-A, 15 W USB-C, 67.5 W USB load power, firmware through Windows Update)](https://learn.microsoft.com/en-us/surface/surface-thunderbolt4-dock)
- [USB-IF: USB 2.0 specification, section 7.2.1 (a unit load is 100 mA; up to five per device; one per port on a bus-powered hub)](https://www.usb.org/document-library/usb-20-specification)
- [USB-IF: USB 3.2 specification (a unit load is 150 mA; up to six per device, 900 mA)](https://www.usb.org/document-library/usb-32-revision-11-june-2022)
- [USB-IF: USB Charger (USB Power Delivery up to 240 W)](https://www.usb.org/usb-charger-pd)
- [Plugable: Self-powered vs bus-powered devices (devices may suddenly disconnect when bus power runs out)](https://kb.plugable.com/usb-hubs-cables-switches/self-powered-vs-bus-powered-devices)
- [Plugable: Hub connectivity (unplug, wait about 30 seconds, power first, then USB)](https://kb.plugable.com/usb-hubs-cables-switches/hub-connectivity)
- [Plugable: Wireless USB device not working on a USB 3.0 hub (use a USB 2.0 port away from USB 3.0 ports)](https://kb.plugable.com/usb-hubs-cables-switches/wireless-usb-device-not-working-on-usb-30-hub)
- [Intel: USB 3.0 radio frequency interference impact on 2.4 GHz wireless devices (white paper 327216-001, copy linked by Plugable)](https://plugable.s3.amazonaws.com/doc/Intel/USB+3.0+Radio+Frequency+Interference+Impact+on+2.4GHz+Wireless+Devices+-+White+Paper.pdf)
- [Dell: WD19TBS dock user guide (update BIOS, drivers and dock firmware; power adapter before the Type-C cable)](https://dl.dell.com/topicspdf/dell-wd19tbs-dock_users-guide_en-us.pdf)
- [DisplayLink: First-step troubleshooting (devices on a dock's USB ports don't go through the DisplayLink chip)](https://support.displaylink.com/knowledgebase/articles/1179748-first-step-troubleshooting-for-devices-powered-by)
- [Plugable: USB devices and video cut out when the USB-C power supply is unplugged from a pass-through port](https://kb.plugable.com/portable-monitors/why-do-my-usb-devices-and-video-cut-out-when-i-disconnect-my-usb-c-power-supply-from-the-pd-pass-through-port)

## Test it yourself

Check your own device with a free test. It runs in your web browser.

- [Keyboard tester](https://devicetests.com/keyboard-tester): Check that every key on your keyboard works.
- [Webcam test](https://devicetests.com/webcam-test): Check that your camera works and see its picture.
- [Mic test](https://devicetests.com/mic-test): Check that your microphone picks up your voice.
