Bufferbloat test

Find out if your internet lags when someone downloads or uploads, and how to fix it.

The test sends and receives random test data only. It carries no personal data, and your results stay in this browser.

We measure your ping at rest, then while downloading and while uploading, and grade how much it rises. It takes about 20 seconds.

Uses up to 300 MB of data on a very fast connection, about 60 MB at 50 Mbps.

Quick start

  1. Pause downloads and video on your other devices.
  2. Press Start bufferbloat test and keep this page on screen.
  3. Read your grade and the fixes under the test.

How to read your results

Your result starts with a grade, from A+ (best) to F, and a sentence like “Your ping rises from 18 ms to 160 ms while uploading”. Then come the numbers.

Ping at rest is how long a tiny message takes to reach our server and come back, in milliseconds (ms), while your connection is quiet. While downloading and while uploading are the average ping while we fill your connection with data in that direction. The grade comes from the bigger rise of the two.

Grade Ping rise while busy What you notice
A+ Under 5 ms Nothing. Your connection stays just as quick when busy.
A 5 to 30 ms Nothing in daily use.
B 30 to 60 ms Fast online games may lag a little when someone downloads.
C 60 to 200 ms Games lag and video calls may stutter while someone downloads or uploads.
D 200 to 400 ms Calls stutter and games lag while anyone downloads or uploads.
F 400 ms or more Calls break up and web pages hang while anyone downloads or uploads.

Each part also shows its worst moments: the ping that only 1 in 20 messages was slower than. Big jumps there mean short lag spikes, even when the average looks fine.

Note: If a ping gets no reply within 3 seconds, we count it as 3 seconds. The result then says “or worse”, because the real average may be higher.

If something’s wrong

These are the most common causes of lag when the line is busy, most likely first. Our guide why is my ping so high covers the other causes of lag too. Slow even when nobody else is online? See why is my internet slow.

What you see What to do
Grade C, D or F Turn on SQM in your router (steps below). Set it to about 90% of your speeds on a cable, then test again.
Upload much worse than download Most lag comes from uploads: photo backups, cloud sync, your camera in a call. Set the upload limit first.
Much better on a network cable than on Wi-Fi Wi-Fi adds the lag. Move closer to the router, put the router in an open, central place, or use a mesh system.
Bad only in the evening Your provider’s network is busy then. Test at different times and show the results to your provider.
Bad with a VPN Turn the VPN off and test again. A VPN adds its own queue far away.
Ping at rest already over 100 ms That isn’t bufferbloat but distance or a slow line. Use the ping test to watch it for longer.
Good grade, but calls still break up Data may get lost on the way. Run the packet loss test.

Turn on SQM in your router

  1. Open your router’s app, or its settings page in a browser (often 192.168.1.1 or 192.168.0.1, printed on the router).
  2. Look for SQM or Smart Queue. On eero it is a switch called SQM, under Settings, Advanced networking, Network services; on Ubiquiti, “Smart Queues”; on OpenWrt, the “sqm-scripts” package. Plain “QoS” that only puts some devices first often doesn’t help.
  3. Enter your download and upload speeds at about 90% of your speed on a network cable, as OpenWrt’s SQM guide advises. Run this test on a computer plugged into the router to get them: speeds on a phone or over Wi-Fi are too low for this. If you can choose a type, pick cake (or fq_codel).
  4. Save, wait a minute, and press Test again. Compare with your last result.

Our guide to QoS and SQM on a router shows the setting on more routers.

No such setting? Many routers from internet providers don’t have one. Update the router’s software, ask your provider for a newer router or modem, or use your own router with SQM behind theirs.

How this test works

When you press Start bufferbloat test, the page connects to our test server and runs three parts:

  1. Ping at rest: it sends 20 tiny messages, up to 10 a second, over a WebSocket (a web connection that stays open) and times each answer. Their average, without the 2 slowest, is your ping at rest: one stray slow answer would otherwise hide the rise.
  2. While downloading: it downloads random data over 4 connections at once for up to 8 seconds, as fast as your line allows, and keeps sending 10 pings a second.
  3. While uploading: the same, with an upload.

The first 1.5 seconds of the download and the first 2 seconds of the upload are not counted, while the connections speed up. The average ping after that, until the part ends, minus your average ping at rest, is the rise. The grade uses the same scale as the well-known Waveform and DSLReports tests, so you can compare.

On a very fast line the test stops after 200 MB down and 100 MB up, so it doesn’t use gigabytes of your data. The result says so when that made a part short. If you switch to another tab or app, browsers slow the page down, so the test stops and you can run it again.

See how we test your internet for where our limits come from, and what a browser can’t measure.

What the test can’t tell you

  • Your lag to other servers. We measure to our one server, at this moment. A game’s server may see more or less.
  • Lag when your line is faster than our server. Then your line isn’t completely full, and the result says so.
  • Exactly where the queue is: your router, your modem or your provider. Testing on a cable, then on Wi-Fi, and at different times narrows it down.

Questions and answers

What is bufferbloat?

When your internet connection is full, your router or modem lets data wait in a long queue. Everything else waits in that queue too, including your video call and your game. So your ping, the time a message takes to get there and back, jumps up. That extra wait is bufferbloat.

It is why a call can freeze when someone starts a big download, even on a fast plan.

How do I fix bufferbloat?

Turn on Smart Queue Management (SQM), also called smart queue, in your router. Set its download and upload limits to about 90% of your speeds on a network cable. The router then keeps the queue short, and small messages like calls and games go first. If your router has no such setting, a router that does fixes it.

What are cake and fq_codel?

They are the two best-known ways a router can keep its queue short. Both are free and built into OpenWrt and many other routers. Cake is newer and easier to set up, and fq_codel uses less processing power. If your router offers either, both work well. Pick cake if you're unsure.

Will SQM make my internet slower?

Your top speed drops by about 5–10%, because the router keeps a little room free. In return your ping stays low when the line is busy, so calls, games and web pages feel faster. For most homes that is a good trade.

Why is my grade different from another bufferbloat test?

Each test measures to its own server, at a different moment, with its own lengths and limits. Other people using your internet during a test also change the result. Grades one letter apart are normal. Test a few times and compare. Our speed test shows the middle value of the pings while busy, this test the average, so their numbers can differ a little.

Does this work on mobile data, 5G or satellite internet?

Yes. Mobile, 5G and satellite connections often have bufferbloat, because their queues are large. The test uses up to 300 MB on a very fast connection, so keep that in mind on a limited data plan.

How much data does the test use?

It depends on your speed. At 50 Mbps it uses about 60 MB. On a very fast line it stops after 200 MB down and 100 MB up, 300 MB at most.