Bubble level
Turn your phone into a spirit level for shelves, frames and furniture.
Your sensor readings stay on your device. We don't record or upload them.
Quick start
- Open this page on your phone or tablet.
- Press Start bubble level. On an iPhone or iPad, tap Allow.
- Lay the phone on the surface, or hold its edge against it.
- Lower the side it says is higher, until it says Level.
How to read your results
The level works in two ways. It picks the right one from how you hold the phone.
| How you hold the phone | What you see | What it measures |
|---|---|---|
| Lying on its back | A round level with a bubble | The tilt in every direction: Side to side and Top to bottom |
| Standing on an edge | A long level, like a spirit level | The tilt along the edge it stands on |
The bubble always moves to the higher side, as in a real spirit level. The words under it say how far off level it is, and which side is higher. At 0.2° or less, it says Level.
Tip: To hang a picture, hold the phone’s long edge against the top of the frame. Turn the frame until the level says Level.
Degrees, percent or inches per foot
Choose how to show the tilt under Show the tilt in, below the buttons. The page remembers your choice. In full screen, the choice is hidden: press Exit full screen to change it.
| Unit | Good for | Example |
|---|---|---|
| Degrees | Pictures, shelves, furniture, appliances | 0.5° is a small tilt you can just see |
| Percent | Patios, paths, ramps, gardens | 2% = 2 cm of rise over 1 metre |
| Inches per foot | Drain pipes, gutters, decks | ¼ inch per foot is a common fall for a drain pipe |
| mm per metre | Floors, tiling, worktops | 3 mm/m is a small slope |
A wheelchair ramp of 1 in 12 is 8.3%, or 4.8°. Always check your local building rules for the slope you need.
Hold reading
In a tight spot, like behind a washing machine or on a high shelf, you can’t see the screen. Put the phone down, press Hold reading and let go. After a moment the number freezes. Then pick up the phone to read it. Press Show live reading to go on.
Calibrate for the best reading
Press Calibrate, then follow the steps:
- Lay the phone on a flat surface and press Mark first spot.
- Turn the phone round, top where the bottom was, on the same spot.
- Press Mark second spot.
The level now knows your phone’s own error, and leaves it out. It also tells you how much the surface itself was tilted. The surface doesn’t need to be level for this to work.
If something’s wrong
These are the most common fixes, easiest first.
Nothing happens, or “No motion sensors found”
- Open this page on your phone or tablet. Computers have no tilt sensor.
- On an iPhone or iPad, press Start bubble level, then tap Allow.
- If you tapped Cancel on an iPhone, close the browser fully and open this page again.
- In Chrome on Android, tap the icon left of the address, then Permissions. Turn on Motion sensors.
It says tilted on a table you know is flat
A case with a bump, or a camera that sticks out, tilts the phone. Take off the case, or press Calibrate and follow the steps. Calibration only works with the phone lying on its back.
The numbers keep moving
Small changes of 0.1° are normal. Put the phone on a firm surface and let go of it. On a soft surface, like a bed or a carpet, the phone sinks unevenly.
It switches between the round and the long level
The level changes when the phone tilts more than about 45°. Lay the phone flat for the round level, or stand it fully on its edge for the long one.
The screen turns while the phone stands on an edge
That’s fine. The long level always lies along the edge the phone stands on, even with the rotation lock on.
The screen turns off
The page asks your phone to keep the screen on while the level runs. Some phones in battery saver ignore this. Turn off battery saver, or tap the screen now and then.
How this test works
Your browser shares the phone’s tilt with web pages, about 60 times a second. The page works out how far the screen is from level in each direction. The bubble moves the full way to the rim at 10° of tilt.
Calibration takes the middle of two readings, turned 180° apart. The surface’s tilt changes sign between them, and the phone’s own error doesn’t, so the middle is the phone’s error. Corrections over 5° are refused. That much comes from a very uneven case or a phone that moved, not from the sensor.
Slope units come from the angle: percent is the rise over 100 units of length, and inches per foot is the rise over 12 inches.
To check what each motion sensor does, use the gyroscope test. See how we test phones and computers for where our limits come from.
What the level can see
- The tilt, shown to a tenth of a degree, lying flat or on an edge.
- Your phone’s own error, after calibration.
What it can’t see
- The sensor’s factory accuracy. Browsers smooth the readings first.
- Whether the edge of your phone is straight. Most are rounded, so lay it on the flattest side.
Questions and answers
How accurate is a phone level?
A phone's tilt sensor is usually right to within a few tenths of a degree. That is good enough for pictures, shelves, furniture and appliances.
A bump on the case or a camera that sticks out can tilt the phone more than that. Press Calibrate once, or take off the case. For building work, use a real spirit level. Measuring lengths is a different job: see how accurate iPhone Measure is.
Is a bubble level the same as a spirit level?
Yes. Both names mean a level with a bubble in a glass tube of liquid. This page draws the same thing, and the bubble moves to the higher side in the same way.
Why does nothing happen on my computer?
Computers have no tilt sensor, so there is nothing to read. Open this page on your phone or tablet. Some 2-in-1 laptops and Windows tablets do have one and work here.
Where is the level on my iPhone?
In the Measure app, in the Utilities folder. Can't find it? See where the Utilities folder is. Open Measure and tap Level. Then hold the iPhone against the object. It turns green when the object is level.
The Camera has a small level too, for straight photos. Open Settings, tap Camera, and turn on Grid and Level.
My phone already has a level. Why use this one?
Use whichever is quicker for you. The iPhone level is inside the Measure app. Many Android phones have none. This page also shows the slope in percent or inches per foot, holds a reading, and tells you which side is higher.
What do percent and inches per foot mean?
They say how much a surface rises over a length. 2% means 2 cm of rise over 1 metre. ¼ inch per foot means a quarter of an inch of rise over each foot of length. Both are about 1.2°.
Does this site record how I tilt my phone?
No. The readings are only used on this page while it is open. If you calibrate, or choose a unit, that small setting is kept in your browser for next time.