Stuck pixel fixer

Try to unstick a pixel that shows the wrong colour.

Press Start fixer. Nothing flashes until you press Start flashing.

Warning: Flashing light

This tool flashes colours fast in a small square. Don't use it if you have photosensitive epilepsy, or if flashing light makes you unwell.

Speed

Fast is the usual way. Slow changes colour twice a second and is gentler. Neither is sure to work.

Run for

Quick start

  1. Press Start fixer. Your screen turns black, with a square on it.
  2. Drag the square over the stuck pixel. Press Start flashing.
  3. Look away. When the time is up, check the pixel.

How to read your results

The fixer can’t see your screen, so you check the pixel yourself after each run. Look at it on the black screen, from about 30 cm (one foot) away.

What you see after a run What it means
The dot is gone The pixel works again. Check it again tomorrow: a freed pixel can get stuck again.
The dot is dimmer, or it flickers The dot has changed. Run the fixer again for 20 or 30 minutes, then check it on black.
No change Run it a few more times. If about an hour in total changes nothing, flashing probably won’t free it.
A black dot on every colour A dead pixel. It gets no power, so flashing can’t fix it.
A speck that moves when you wipe Dust or a hair on the glass, not a pixel.

Only stuck pixels can come back:

Kind of dot How it looks Can the fixer help?
Stuck pixel A bright red, green, blue or white dot. Easiest to see on black. Sometimes.
Dead pixel A black dot on every colour. Easiest to see on white. No.
Dust or a scratch A grey speck, often bigger than one pixel. No. Wipe the screen.

Not sure which kind you have? Fill your screen with colours in the dead pixel test first.

Tip: Before you start, take a photo of the dot on a black screen. If you need the warranty later, the photo shows what was there.

If something’s wrong

These are the most common problems, most likely first.

I can’t find the stuck pixel

Press Start fixer: the screen turns black, so a lit pixel stands out. Look closely, from about 30 cm (one foot) away. If the dot only shows on another colour, find it with the dead pixel test and note where it is.

The dot is still there after the fixer

  1. Run the fixer 2 or 3 more times, for 20 or 30 minutes each.
  2. Turn the screen off for a few hours, then look again.
  3. If it stays, check the warranty, as shown below.

I want to check the warranty

  1. Take a photo of the dot on a black screen, and keep your receipt.
  2. Look up the “pixel policy” for your model on the maker’s website. Some makers replace a screen for one bright dot.
  3. If the screen is new, ask the shop first: its return period is often the easiest way.

Should I press on the pixel?

Some people press gently on a stuck pixel through a soft cloth, and say it helped. We don’t recommend it:

  • It can crack the screen or damage more pixels.
  • Some makers, such as Dell, warn that it can void the warranty.
  • Never try it on a phone, a tablet or an OLED screen, and never with a pen or a fingernail.

Note: Check the warranty before you try anything that touches the screen.

The square can’t reach the edge of my iPhone screen

Safari can’t make a page full screen on an iPhone, so its bars cover the very top and bottom edges. Turn your phone sideways: the bars get smaller. In Safari, tap the page menu next to the address, then Hide Toolbar, if you have it.

The screen dims or turns off during the run

Most browsers keep the screen on while the fixer runs. Battery saver can stop that. Plug the device in, or set the screen to turn off after a longer time.

The flashing stopped by itself

The flashing pauses when you tap or click anywhere, and when you switch to another tab or app, so it never runs where you can’t stop it. Press Resume flashing to go on. When the time is up, it stops and the square shows as a frame again.

The flashing makes me feel unwell

Stop at once: press Esc, or tap or click anywhere. Look away from the screen. Ask someone else to run the fixer, and stay out of the room while it flashes.

How this test works

The fixer shows a small square on a black screen. You line it up over the stuck pixel while it is still, then start the flashing. To move it again, pause first.

In the Fast mode, every pixel in the square gets a new random colour each time the screen redraws, 60 or more times a second. Each pixel’s three tiny lights, red, green and blue, switch on and off over and over. Sometimes this frees a light that is stuck on. The Slow mode changes the whole square’s colour twice a second. It is gentler. Neither mode is sure to work.

The timer counts only the time the square flashes. While the fixer runs, the screen stays on.

How we keep the flashing safer

  • Nothing flashes until you press Start flashing. If your device is set to reduce motion, Slow is chosen and the fixer asks once more.
  • The square is small: about 3 to 4 cm (1.5 inches) across at most on a computer screen, and smaller on phones. It never fills the whole screen.
  • The fast mode is fine noise, one pixel at a time, so the square’s overall brightness hardly changes. Safety guidelines treat fine noise like this as much less risky than a flashing area.
  • The slow mode stays under the safety limit of 3 flashes a second.
  • A tap, a click, Space or Esc stops the flashing at once. It also pauses when you switch away.

No flashing tool is safe for everyone. If flashing light affects you, don’t use it.

See how we test screens for where our limits come from, and what a browser can’t measure.

What the fixer can do

  • Sometimes free a stuck pixel, especially one that got stuck recently.

What it can’t do

  • Fix a dead pixel, a crack, lines, pressure marks or burn-in.
  • See your screen: only you can tell whether the dot has gone.

Questions and answers

Does a stuck pixel fixer really work?

Sometimes. People often report that flashing freed a stuck pixel, but there are no proper studies, and no one can promise it will work. It has the best chance on a pixel that got stuck recently.

It can't fix a dead pixel, which stays black on every colour. If a few runs that add up to about an hour change nothing, flashing probably won't free it.

Is it safe if I have photosensitive epilepsy?

Flashing light can cause seizures in people with photosensitive epilepsy. If that's you, don't use this tool. Ask someone else to start it, and stay out of the room while it runs.

Nothing flashes until you press Start flashing. The square is small, and the fast mode uses fine noise rather than big flashes. The slow mode changes colour only twice a second. A tap, a click or Esc stops it at once.

Can the fixer damage my screen?

Showing changing colours is ordinary work for a screen, and we know of no screen damaged by a short run. Some makers, such as Dell, still advise against pixel-fixing tools, so check your maker's advice and warranty first.

On an OLED screen, such as many phones, keep to the run times here rather than leaving it on for hours.

Should I press or rub the stuck pixel?

We don't recommend it. Pressing can crack the screen or damage more pixels, and some makers say it can void the warranty.

Check the warranty first. Never press on a phone, a tablet or an OLED screen. See "Should I press on the pixel?" above for the risks.

How long should I run the fixer?

Start with 10 minutes. If the dot is still there, run it 2 or 3 more times for 20 or 30 minutes. Some people leave it longer, but if about an hour in total changes nothing, it's time to check the warranty.

Does it work on phones, tablets and TVs?

Yes on Android phones and tablets and on an iPad: the fixer fills the whole screen. On an iPhone, it fills the browser window, so the very top and bottom edges are out of reach.

For a TV, open this page in the TV's own browser, or connect a computer to the TV and run it there. A video of flashing colours is less likely to work, because video is compressed and doesn't change every pixel.

I have more than one stuck pixel. What do I do?

If the dots are close together, press Bigger until the square covers them all. If they're far apart, run the fixer once for each one.

How many stuck pixels does a warranty cover?

It depends on the maker, the model and the shop. Many makers have a "pixel policy" that counts bright dots more strictly than dark ones, and some replace a screen for a single bright dot. A new screen is often easiest to return to the shop within its return period.

Our dead pixel policy guide lists the limits brand by brand.