Printer test page
Print a test page to check your printer’s colours, black ink and alignment.
Press Print this page, or choose another page first.
In the print window, choose your printer and keep the scale at 100% (Default or Actual size).
Thin strips instead of large blocks. Streaks and missing colours still show.
Rough estimate: this page covers about 12% of the paper with ink. A typical page of text covers about 5%.
Quick start
- Choose a page. Everything on one page is a good start.
- Press Print this page, then choose your printer.
- Compare your print with the pictures under How to read your print.
How to read your print
Hold the print under good light. Look at the blocks of colour first, then the greys, then the lines.
| What you see | What it means |
|---|---|
| Even blocks, neutral greys | No obvious print problems. Lines are sharp, and the rulers measure 100 mm and 4 inches. |
| White lines or streaks across a colour | On an inkjet, most often blocked nozzles in the print head. Common after a printer sits unused. |
| A colour is missing | That ink is empty, blocked, or the cartridge still has its tape on. The greys usually turn a colour too. |
| Everything looks pale | Low ink, draft or ink saving mode, or the wrong paper setting. |
| Greys look pink, green or blue | Often one ink is weak or blocked. A colour setting or the paper can also tint greys. |
| Lines look doubled, blurry or don’t meet | An inkjet’s print head needs aligning. On a colour laser, the colours need calibrating. |
| Smudges or smears | The paper setting doesn’t match the paper, the paper is damp or curled, or the rollers are dirty. |
| A pale stripe down the page (laser) | Low toner, a dirty laser window or a worn drum. |
| The same mark repeats down the page (laser) | Something on a roller or the drum. The gap between the marks tells you which part. |
| A corner mark is missing, or the page is cut off | The paper size or the scale is wrong, or the paper went in crooked. |
Many printers mix greys from cyan, magenta and yellow. If a tint is new, it is a clue to which ink is weak:
| Greys look | Ink to check first |
|---|---|
| Pink or red | Cyan |
| Green | Magenta |
| Blue or purple | Yellow |
The fine lines show gaps and uneven printing. A gap or a missing line often means a blocked nozzle, but only your printer’s own nozzle check shows each nozzle. The rulers should measure exactly 100 mm and 4 inches. If they are shorter, the page was shrunk to fit.
Note: A web page goes through your computer’s printer settings, so one blocked nozzle can hide in the mix. If you see streaks, run your printer’s own nozzle check to be sure. See “How this test page works” below.
If something’s wrong
These are the most common problems, most likely first.
Nothing prints, or the page is blank
- Check that the printer is on, has paper and shows no error on its screen.
- Check that you chose the right printer in the print window.
- Make sure no cartridge still has its orange tape or plastic clip on.
- Print your printer’s own test page (see the FAQ). If that is blank too, the problem is in the printer, not the computer.
The printer shows as offline
- Turn the printer off and unplug it. Wait 30 seconds, then plug it back in. Restart the computer too.
- Check that the printer and the computer are on the same Wi-Fi. If you use a network printer, restart the router.
- On Windows, cancel all stuck jobs in the printer’s print queue.
- Windows 11: in Settings, Bluetooth & devices, Printers & scanners, choose your printer, then Set as default. Windows 10: open the print queue, choose Printer, then Set As Default Printer, and clear Pause Printing and Use Printer Offline.
- HP printer: open the HP app, click the printer, then Diagnose & Fix.
- Still offline? Remove the printer, then add it again.
Sources: Microsoft’s Troubleshooting offline printer problems and HP’s HP printer is offline or unavailable.
White lines or streaks across the colours
- Run your printer’s nozzle check from its menu or app.
- If it shows gaps, run head cleaning once, then the nozzle check again.
- Still gaps? Follow your printer’s manual for more cleanings and how long to wait between them, often 12 hours to a day.
- If a colour never comes back, the cartridge or the print head may need replacing. Your printer’s support line can tell you which.
Your printer isn’t printing black
Print the Black and white page here first. If its black blocks are blank, pale or striped, the black ink isn’t getting through.
- Check the black ink in the printer’s app or on its screen. On an ink tank printer, such as an Epson EcoTank, the black tank must be above its lower line. Refill or replace it if it’s low.
- New cartridge? Take off all the tape and caps, as its box shows. Push it in until it clicks.
- Run a nozzle check. Nozzles are the tiny holes that spray the ink. Gaps in the black pattern mean they are blocked. Run head cleaning once, then the nozzle check again.
- Still gaps after 2 or 3 cleanings? Turn the printer off and let it rest for at least 12 hours. Dried ink often softens by then. Then run the nozzle check again.
- Third-party or refilled cartridge? Try a new one from your printer’s maker. Some aren’t recognised, or don’t let ink through well.
- Nozzle check is fine, but your pages aren’t? Then the problem is on the computer. Set the paper type to the paper you use, and try Grayscale or Black and white. If that doesn’t help, reinstall the driver from the printer maker’s website.
Epson printers:
- Nozzle check and head cleaning are under Maintenance on the printer’s screen. On Windows, open your printer’s Printing Preferences, then the Maintenance or Utility tab.
- Each cleaning uses a lot of ink and fills an ink pad inside the printer. When that pad is full, the printer stops until Epson services it. So don’t clean again and again.
- Many EcoTank printers also have Power Cleaning for blocks that stay. It uses even more ink. Each tank must be at least a third full first.
- On Windows, some Epson printers offer to mix black from the colour inks when black runs low. Black text then looks dark grey or brown.
A colour is missing, or the greys have a tint
- Check that you printed in colour, not Black and white or Greyscale.
- Check the ink levels in the printer’s app or on its screen.
- Run the nozzle check and look at that colour.
- Clean the print head as above.
- Take the cartridge out and put it back firmly. Replace it if it’s empty or old.
Everything looks pale or faded
- In the print window, choose Standard or High quality, not Draft or Economy.
- Set the paper type to the paper you use, such as Plain paper.
- Check the ink levels. On a laser printer, turn off toner save.
Lines look doubled, blurry or don’t meet
Inkjet
- Run print head alignment from the printer’s menu or app.
- Turn off high speed or two-way printing in the print settings, then print again.
- Use flat, dry paper, and set the paper type to match it.
Colour laser
- Run colour calibration or colour registration from the printer’s menu.
- Check that every toner cartridge and the drum are seated firmly.
Smudges, smears or ink marks
- Set the paper type to the paper in the tray. Thick or photo paper needs its own setting.
- Use dry, flat paper. Fan the stack before you load it.
- Clean the rollers with the printer’s paper guide cleaning, or a lint-free cloth and a little water.
- Let the print dry for a minute before you touch it.
The page is cut off, or the ruler isn’t 100 mm
- Choose the paper size in the tray: A4 or US Letter, on this page and in the print window.
- Set the scale to 100%, Actual size or Default, not Fit to page.
- Straighten the paper guides in the tray.
- Safari: in the print window, untick Print headers and footers. Older browsers may add their own margins or lines: press Download PDF and print the PDF at 100% instead.
- iPhones and iPads always shrink the page a little to fit the printer’s margins, so the rulers measure a few millimetres short there. That’s normal.
Laser printer: a pale stripe down the page
- Take the toner cartridge out and gently rock it from side to side, then put it back.
- Run the printer’s cleaning page from its menu.
- On Brother printers, slide the green tab on the drum from side to side a few times, then put it back in its home position, marked with a triangle. A tab left out of place causes a stripe itself.
- Clean the laser window or LED heads as your printer’s manual shows.
- If the stripe stays, check the toner level. Replace the toner or the drum when the printer or its manual points to that part.
Laser printer: a dark line down the page
- Clean the corona wire: on Brother printers, slide the green tab on the drum from side to side a few times, then put it back in its home position.
- Look at the drum for a scratch or a speck of dirt, without touching its surface.
- If the line stays, the drum may need replacing. Check with your printer’s manual first.
Laser printer: marks that repeat down the page
Measure the gap between two marks. Each roller makes a mark once per turn, so the gap tells you which part it is. Look up the gap in your printer’s manual or the maker’s support page. A gap of about 94 to 96 mm is often the drum.
Your phone can’t find the printer
- Put the phone and the printer on the same Wi-Fi.
- iPhone and iPad: the printer must support AirPrint. Most Wi-Fi printers do.
- Android: open Settings, search for Printing, and turn on the Default Print Service or Mopria. Your printer maker’s app also adds its printers.
- Or download the PDF and print it from the printer maker’s app.
How this test page works
The page is drawn as a vector picture in millimetres, not as a photo, so lines and edges are as sharp as your printer can make them. Some test pages print a compressed picture, where blurry edges come from the picture, not the printer. The page fits on both A4 and US Letter, inside the margins most printers need, and in current browsers it prints without the browser’s date and address lines. The PDF is made in your browser and holds the same page.
What it can show
- Streaks, gaps, missing or faded colours.
- A colour tint in the greys, and which ink causes it.
- Blurry or doubled lines, and colours that don’t line up.
- Smudges, and pages that are cut off or printed at the wrong size.
What it can’t show
- Which single nozzle is blocked. Your printer’s own nozzle check prints every nozzle row of each ink, so it’s the better check.
- Ink levels or errors: a web page can’t talk to your printer.
- Exact colour accuracy, which needs a measuring device.
Your printer’s own checks skip the computer and its settings. Use them for nozzles, cleaning and alignment:
| Printer | Nozzle check and cleaning | Alignment |
|---|---|---|
| Epson | Maintenance on the printer’s screen, or the Maintenance tab in the printer’s settings on Windows. Many models allow up to 3 cleanings, then a wait of at least 12 hours. | Print Head Alignment, in the same menu. |
| Canon | Maintenance on the printer, or the Canon IJ Printer Assistant on a computer. Usually Cleaning first, then Deep Cleaning, then 24 hours before another deep clean. | Print Head Alignment, often automatic. |
| HP | Setup or Tools, Reports, Print Quality Report. Clean Printheads runs in up to 3 stages. | Align Printheads, in the same menu. |
| Brother | Ink, Improve Print Quality, Check Print Quality. Brother advises against more than 5 cleanings in a row. | Alignment, in the same menu. |
On a Mac, open System Settings, Printers and Scanners, choose your printer, then Options and Supplies, Utility, where your printer offers it. Menu names change from model to model, so check your printer’s manual if you can’t find them.
See how we make this test page for what it shows, and what only your printer’s own check can show.
Questions and answers
How do I print my printer’s own test page?
Windows 11: Start, Settings, Bluetooth & devices, Printers & scanners. Choose your printer, then Printer properties. On the General tab, choose Print Test Page.
Windows 10: Start, Settings, Devices, Printers & scanners. Choose your printer, then Manage, then Printer properties. On the General tab, choose Print Test Page.
Mac: open the print queue (Print Center in newer macOS). It opens when you print something, and it is also in the Utilities folder in Applications. Choose your printer, then Printer, Print Test Page in the menu bar.
HP: the steps differ by model. In the HP app, click your printer, then Printer Reports under Tools. Some models print a report when you hold a button on the printer: see its manual.
On the printer: most printers print their own page from the Setup, Tools or Maintenance menu on their screen. The table under "How this test page works" lists the menus for Epson, Canon, HP and Brother.
How many times should I run head cleaning?
Start with one. Run the nozzle check, clean once if it shows gaps, then check again. Each cleaning pushes ink through the print head, so it uses a lot of ink. Your printer’s manual says how many cleanings to run in a row and how long to wait before more. That is often 2 or 3, then a wait of 12 hours to a day, depending on the model.
How much ink does a test page use?
The page shows a rough estimate under the choices. A typical page of text covers about 5% of the paper with ink. The Colour page covers much more. Turn on Use less ink for thin strips instead of large blocks, or choose Alignment and fine lines, which uses very little.
Why is my printer not printing black?
Most often the black ink is empty, or the black nozzles in the print head are blocked by dried ink. Print the Black and white page here, then run your printer’s nozzle check. Epson, Canon, HP and Brother printers all have one.
The steps, with tips for Epson printers, are under "Your printer isn’t printing black" in "If something’s wrong".
How do I print with only black ink?
Choose Black and white page, then look for Black ink only (some printers call it Black cartridge only) in the print settings. Black and white or Greyscale is not the same on every printer: some still mix colour inks into greys.
When should I download the PDF?
Use the PDF to print from another computer or a printer app, from a USB stick, or at a print shop. It also prints without the browser’s own lines, such as the date and the web address. When you print it, set the scale to 100% or Actual size: in Chrome and Edge, choose Scale, Custom, 100. Many PDF viewers shrink the page to fit by default.
Can I print this from my phone?
Yes. On an iPhone or iPad, Print this page opens the print options, where AirPrint printers show up. On Android it opens the print screen, which uses a print service such as Mopria or your printer maker’s plug-in. You can also download the PDF and print it from the printer’s app.
Does this work with a laser printer?
Yes. Laser printers don’t have nozzles, so ignore the nozzle advice. Look for faded stripes, lines and repeating marks instead. The fixes are under "If something’s wrong".
Why do colours on paper look different from my screen?
A screen makes colour with light and paper with ink, so they never match exactly. Bright blues and greens look duller on paper. Plain paper also soaks up ink, so photo paper looks much richer. Judge the print by streaks, gaps and tints, not by matching the screen. Printing photos? See print a photo at the right size.
Can this page see my printer or its ink levels?
No. A web page can’t talk to your printer. It only sends a page through your computer’s or phone’s normal print window. Ink levels are in your printer’s app or on its screen.