DPI analyzer
Find your mouse’s real DPI by moving it along a bank card, a sheet of paper or a ruler.
Pick what you will measure along, then press Start measuring.
The long side of a bank or credit card: 8.56 cm (3.37 in).
Quick start
- Pick what you will measure along, for example a Bank card.
- Press Start measuring and line your mouse up with the left end.
- Hold the left button, slide to the right end, let go. Do it 3 times.
How to read your results
Your result is the middle of three runs: how many steps your mouse reported for each inch you moved it.
| What you see | What it means |
|---|---|
| DPI | Raw counts from your mouse for each inch. This is your mouse’s real DPI. |
| Pixels per inch | How far the pointer moved for each inch. Your browser couldn’t read raw counts, so your pointer settings are part of it. |
| Your runs | Each run’s result. They should be within a few percent of each other. |
| Spread | The highest run minus the lowest, as a share. Under 3% means a steady measurement. |
| Probably set to | A common DPI step close to your result, such as 800 or 1600. Mice are often a few percent off their setting. |
Tip: The longer the distance, the more exact the result. A sheet of A4 or Letter paper is about four times more exact than a bank card.
If something’s wrong
These are the most common problems, most likely first.
My runs are far apart
Slide slowly, in a straight line along the edge, and keep the mouse flat on the desk. Line up the same side of the mouse with each end every time. Lifting the mouse during a run loses steps.
My result says pixels per inch, not DPI
Your browser couldn’t read raw counts from the mouse. Open this page in Chrome or Edge on Windows or a Mac, or in Safari 18.4 or later. If you stay in this browser, set your pointer to neutral first.
Windows
- Open Settings, then Bluetooth and devices, then Mouse, then Additional mouse settings.
- On the Pointer Options tab, turn off Enhance pointer precision.
- Move the pointer speed slider to the middle notch.
Mac
- Open System Settings, then Mouse, then Advanced.
- Turn off Pointer acceleration (macOS 14 and later).
- Tracking speed still scales the reading.
The result is about double or half what I expected
Your mouse is probably on another DPI step. Many mice have a DPI button that cycles through steps. Check the light on the mouse or the maker’s app, then measure again.
The pointer reached the edge of the screen
Without a locked pointer, the pointer stops at the screen’s edge and the run is too short. Pick a shorter distance, such as the bank card, or use a browser that locks the pointer.
Nothing happens when I press Start measuring
If you pressed Esc just before, wait a second and try again: browsers refuse to lock the pointer again straight away. On a phone or tablet with no mouse, the test can’t run.
How this test works
When you press Start measuring, the page locks the pointer to the measuring area, the way games do. We ask your browser for raw movement: the steps your mouse sends, before Windows or macOS apply pointer speed or acceleration. Chrome and Edge on Windows, Mac and ChromeOS have it, and so do Safari 18.4 and later, and Firefox 152 and later on Windows and Mac.
While you hold the left button, we add up every step you move. When you let go, we divide the steps by the distance in inches. A run that is very short, or goes far sideways, doesn’t count. After three runs, the result is the middle one.
Where raw movement isn’t available
- With a plain pointer lock, the movement follows your system pointer. The result is pixels per inch, after your pointer speed and acceleration. We take browser zoom out, but on a Mac the screen scaling can still change it.
- With no pointer lock at all, we follow the pointer on screen. It stops at the screen’s edge, so long moves can come out short.
We never claim a DPI from these modes: the result says pixels per inch. Your mouse sends nothing else we could read, so no web page can see its DPI setting directly. See how we test for what a browser can and can’t measure.
Questions and answers
How do I check my mouse DPI without software?
Windows and macOS don’t show your mouse’s DPI anywhere. You can find it three ways. Look up your mouse’s model: the maker lists its DPI steps. Open the mouse maker’s app, such as Logitech G HUB or Razer Synapse, which shows the current setting. Or measure it here: move the mouse a known distance and we count the steps it reports.
How accurate is this DPI test?
With raw counts, it is usually within 1 to 2 percent, if you line the mouse up carefully. The main error is you: 1 mm off at the end of a bank card is about 1.2 percent. On a sheet of A4 or Letter paper, it is about 0.3 percent. Slide slowly and straight, and keep the mouse flat.
Why doesn’t my result match the DPI on the box?
Many mice measure a few percent above or below the number they are set to. That is normal and doesn’t change how they feel. A bigger difference usually means the mouse is set to another DPI step, often by a DPI button on top or under the mouse.
If your result says pixels per inch instead of DPI, your browser couldn’t read raw counts, so your pointer settings are part of the number.
What does the DPI button on my mouse do?
DPI (dots per inch) is how many steps your mouse reports for each inch you move it, so it sets how fast the pointer goes. The DPI button switches between a few DPI steps, for example 800, 1600 and 3200. On a higher step, the pointer moves further for the same hand movement. The button usually sits behind the scroll wheel, sometimes under the mouse. Many mice show the step with a light or a colour.
To find out what each step really is, measure the current one here. Then press the DPI button once and measure again. On most mice, each press moves to the next step.
If your mouse supports it, its maker’s app, such as Logitech G HUB or Razer Synapse, lets you change the steps or what the button does. If the pointer speed never changes when you press it, the button may be set to do something else in that app, or all the steps may be set to the same number.
Do Windows pointer speed or Enhance pointer precision change my DPI?
No. They change how far the pointer moves on screen, not what the mouse sends. Games that read raw input ignore them. Our raw mode ignores them too.
They do change a pixels-per-inch reading. On Windows, it equals your DPI only with the pointer speed at the middle notch and Enhance pointer precision off.
What is the difference between DPI and CPI?
DPI (dots per inch) and CPI (counts per inch) mean the same thing for a mouse: how many steps it reports for each inch you move it. Makers use both words.
What DPI should I use for gaming?
Most pro players use 400 to 1600 DPI, and 800 is the most common. A higher DPI isn’t better by itself. What matters is how far you move the mouse for a full turn in your game, which is your DPI and your game’s sensitivity together. The sens converter shows it as cm/360. To set your mouse to 800, see how to change the mouse DPI.
Can I measure my laptop’s trackpad?
No. A trackpad has no DPI: it measures your finger, and the system decides how far the pointer goes. The browser reports it like a mouse, so the page can’t tell. Use a mouse for this test.
Can I check the DPI on a phone or tablet?
Only with a mouse connected. A touch screen has no DPI, so the test needs a mouse to count.