Audio latency test
See how late your sound is, from Bluetooth earbuds to TV speakers, and how to fix it.
The tap test needs no microphone, and no sound is recorded or uploaded.
Round 2 flashes a light about once a second.
Quick start
- Connect the headphones or speakers you want to check.
- Press Start tap test, then tap with each click.
- Press Start round 2, then tap with each flash.
How to read your results
The tap test gives up to five numbers. Each one is in milliseconds (ms): 1,000 ms is one second.
| Number | What it means |
|---|---|
| Sound against picture | How much later the sound arrives than the picture. This decides your result. |
| Sound delay since last time | The change in sound delay since your last run. Run the test once with wired headphones or the built-in speakers, then with Bluetooth. The difference is what Bluetooth adds. |
| Sound delay | How long after each click your taps came. It includes your own timing, so compare it between runs. |
| Picture delay | How long after each flash your taps came. It includes your screen and your own timing. |
| Browser-reported output delay | What your browser says its sound path adds. Often it leaves out Bluetooth. |
The microphone test gives a round trip: the time from playing a chirp to hearing it in the microphone. It includes the speaker and the microphone, so it is a little more than the speaker delay alone.
Typical delays. These vary from device to device. Your numbers also include your browser and system, often another 20 to 60 ms, and more on some Android phones.
| Sound through | Typical delay |
|---|---|
| Built-in speakers, wired headphones | almost none |
| Gaming headset with its own USB dongle (2.4 GHz) | about 20 to 40 ms |
| Bluetooth with aptX Low Latency | about 40 ms |
| Bluetooth with aptX Adaptive | about 80 ms |
| Most Bluetooth headphones and earbuds (the basic SBC codec) | about 170 to 260 ms |
These figures come from RTINGS, which measured 27 headphones in 2023 (dongles 22 to 42 ms; SBC about 170 ms on gaming headsets and 260 ms on other headphones and earbuds), and from Qualcomm for aptX.
Tip: A codec is the way Bluetooth squeezes the sound. Your phone and headphones pick the best one they both know. Newer devices with LE Audio can get under 50 ms.
If something’s wrong
These are the most common problems, most likely first.
Sound is late in games or calls: fixing Bluetooth delay
Bluetooth always adds some delay. These steps can make it smaller. Run the tap test again after each one, and compare Sound delay since last time.
- Turn on game mode (sometimes called low latency mode) in your earbuds’ app or settings. Some Samsung Galaxy Buds have it: open the Bluetooth settings on your phone, tap your Buds, then Setup your earbuds, Earbud settings, Labs, and turn on Gaming mode. Many other brands have it too.
- Use a cable for games and music apps. Wired headphones add almost no delay.
- Use a 2.4 GHz dongle. Gaming headsets with a USB dongle are much faster than Bluetooth. See Bluetooth vs 2.4 GHz vs wired.
- Keep the connection clear. Samsung advises moving the devices closer together, with no metal, walls or people between them. Keep away from other Bluetooth devices, microwaves and Wi-Fi routers.
- On Android, check the codec. Turn on Developer options: tap Build number 7 times in Settings, About phone. Then open Developer options, Bluetooth audio codec. aptX Adaptive or aptX Low Latency are fastest, if your headphones have them.
- Set an offset in the game. Rhythm games such as osu! and Fortnite Festival have an audio offset or a calibration. Run it with the headphones you play with.
For films and TV, the delay is fixed differently: see the TV settings below. For fast games on a TV, Sony’s TV guide advises against Bluetooth. Use the TV’s speakers or a wired sound system.
Still late with a cable? Then check your game’s or app’s own sound settings.
Lips don’t match on the TV
Your TV can usually only hold the sound back. That fixes sound that comes too early. Sound that comes late needs the TV to hold the picture back. Many TVs do that by themselves for Bluetooth headphones.
| TV or box | Where the setting is |
|---|---|
| Samsung | Settings, Sound, Expert Settings, Digital Output Audio Delay (for soundbars and receivers) |
| LG | Settings, Sound, Additional Settings, AV Sync Adjustment (on some models Match Screen and Sound) |
| Sony (Google TV) | Settings, Display and Sound, Audio output, A/V sync |
| Apple TV | Settings, Video and Audio, Wireless Audio Sync (uses your iPhone to measure) |
| Other TVs | Look in the Sound or Audio settings for A/V sync, Lip sync or Audio delay. |
Tip: Does the sound come before the picture? Turn off picture processing, such as motion smoothing, or use the TV’s Game picture mode. Both make the picture faster. If the sound comes after the picture, a faster picture makes the gap bigger.
Using a TV as a computer screen? See the TV’s sound settings.
A video on your computer is out of sync
- VLC on Windows or Linux: press J to play the sound 50 ms earlier, and K for 50 ms later. Or open Tools, Track Synchronization.
- VLC on a Mac: press F for earlier and G for later. Or open Window, Track Synchronization.
- In a browser: websites can’t change the delay. Restart the video after connecting your headphones. Some sites then catch up.
The microphone test didn’t hear the chirps
- Turn the volume up to a normal listening level.
- Use speakers, or hold one earbud right next to the microphone. Headphones on your ears keep the sound from the microphone.
- Choose your computer’s or phone’s own microphone, not the one in your headset.
- Keep the room quiet, and press Start microphone test again.
Your taps were scattered
- Tap with a steady rhythm, like clapping to music, rather than reacting to each click.
- Use Space on a keyboard or a mouse button. They are easier to time than a touch screen.
- Close other apps and tabs. A busy computer can make clicks and flashes stutter.
No sound at all
- Turn up the volume, and check that your device isn’t muted.
- Check that the sound goes to the headphones or speakers you want to test.
- iPhone or iPad: turn off Silent mode.
How this test works
Tap test. Round 1 plays a click every 0.8 seconds, 19 times. The first 3 are a count-in. Round 2 flashes a light at the same pace, with no sound. Each tap is matched to its beat, from 200 ms before it to 600 ms after it. We use the middle value of at least 8 taps, and ignore taps far from the others.
The sound delay is measured from the moment your browser plays the click. So it includes everything after that: the browser, your system, Bluetooth and the air. The picture delay includes your screen. Sound against picture is the difference between the two.
People time sounds and lights a little differently, by a few tens of ms. So a small number either way means “in sync”. The result only calls the sound late from 80 ms. If your taps in a round are too spread out, the result says so instead of giving a verdict.
Microphone test. Echo cancellation and noise reduction are turned off, so the chirps reach us as they are. The test plays 8 short chirps, about one a second. It finds each chirp in the microphone sound and times it. We use the middle value of at least 4 chirps that came back at the same delay, so a knock or a voice in the room isn’t counted.
What your browser reports. Chrome, Edge, Firefox and Safari 18.4 or later report an output delay. It is shown when your browser gives one. A missing value doesn’t mean there is no delay.
Limits. The tap test includes your own timing, so compare runs rather than reading one number on its own. A screen adds its own delay to the picture round. The beat repeats every 0.8 seconds, so a delay of more than 600 ms (rare, but possible when casting to a TV) reads as too small. These are estimates for comparing, not lab measurements. Sources for the thresholds: ITU-R BT.1359 (when people notice a sound and picture delay).
Questions and answers
Why is Bluetooth audio delayed?
Bluetooth squeezes the sound so it fits through the air, then sends it in small packets. The earbuds wait for a few packets before they play, so the sound doesn't break up. That waiting adds about 100 to 300 ms.
Wired headphones send the sound straight away, so they add almost nothing.
Why do films look fine but games feel late?
Video apps such as YouTube, Netflix and most TV apps know about the Bluetooth delay. They hold the picture back by the same amount, so lips match.
A game can't wait: it has to react to you at once. So in games, calls and music apps you still hear the delay.
Does this test measure my reaction time?
No. You tap along with a steady beat, the way you clap to music. People land on the beat rather than react to it, so reaction time isn't in the number. Your timing habits still are, which is why comparing two runs gives the clearest answer.
Can I measure AirPods or other earbuds with the microphone?
Yes, if you take one earbud out and hold it right next to your phone's or computer's microphone. Don't use the earbuds' own microphone. Using it switches Bluetooth to call mode, which changes the delay and the sound. See why headphones sound bad in call mode.
Why does my browser report a smaller delay?
Browsers can only see their own part of the path and what the system tells them. Many systems leave out the time inside Bluetooth headphones. That's why the tap test and the microphone test usually show more.
How do I test other speakers or headphones?
In Chrome or Edge on a computer, pick them in the Play through list. In other browsers, choose them in your device's sound settings first.
What delay can I live with?
Most people notice sound that comes more than about 125 ms after the picture, or more than 45 ms before it. For fast games and playing music, less than 50 ms feels best.
Guides for this test
- Bluetooth vs 2.4 GHz Dongle vs Wired: How Much Lag Does Each Add?Bluetooth, a 2.4 GHz dongle or a cable for your mouse, keyboard, controller or headphones? What each adds in ms, what you can feel, and how to check yours.
- Using a TV as a Computer Monitor or for Gaming: The Settings That MatterBlurry text, lag or only 60 Hz on your TV? Pick your TV and what you use it for, and get the settings in order: port, PC mode, Game mode, 120 Hz and sound.