Surround sound test

Check each 5.1 or 7.1 speaker and the subwoofer, one by one.

Turn your volume down first. Each speaker plays a soft hiss, the subwoofer a low rumble.

Quick start

  1. Turn your volume down, then press Start test.
  2. Press each speaker in the picture and listen.
  3. Choose where you heard it, then press Show my result.

How to read your results

The test first shows how many channels your computer sends to this page. That decides which speakers it can check.

Channels found What you can check
8 channels: 7.1 Front left and right, centre, subwoofer, side left and right, back left and right.
6 channels: 5.1 Front left and right, centre, subwoofer, surround left and right.
4 channels: 4.0 Front left and right, rear left and right, and the bass.
2 channels: stereo Only front left and right, and the bass. Set up 5.1 or 7.1 to check more.

Press a speaker in the picture. It turns orange while it plays a soft hiss four times. Then choose where you heard it:

You heard it What it means
Only from this speaker That speaker works and is in the right place.
From other speakers The channel goes to the wrong speaker. Two wires or settings may be swapped.
Nothing The speaker is off, not connected, or turned off in the receiver’s setup.

The subwoofer plays a low rumble instead of a hiss. If it comes from your other speakers, the receiver is set to have no subwoofer. That is fine if you have none.

When every speaker is answered, a bar at the top of the test says in words what you found, such as “Only the front left and right speakers played.” Press Show my result to see what to do next. Continue test takes you back to the speakers, with your answers kept.

Play each in turn goes round the room once, clockwise from the front left, with the subwoofer last. It is a quick way to hear the whole circle.

Tip: If one speaker sounds much louder or quieter than the rest, use your receiver’s own test tone or automatic setup to even out the levels. A browser can’t measure how loud each speaker is.

If something’s wrong

These are the most common problems, most likely first.

Only 2 channels found

Most often, your computer is set to stereo. Change it, then press Check again.

Windows

  • Open Sound settings, then More sound settings.
  • Choose your receiver or HDMI output and press Set Default.
  • Press Configure, choose 5.1 Surround or 7.1 Surround.
  • Tick every speaker you have, then press Finish.

Mac

  • Open Audio MIDI Setup (in Applications, then Utilities).
  • Choose your HDMI or receiver output. Set its format to 6 or 8 channels.
  • Press Configure Speakers. In the Configuration menu, choose 5.1 Surround or a 7.1 layout.
  • Press each speaker’s Test button to check which speaker gets which channel, then press Apply.

If 5.1 and 7.1 are missing, your connection carries only stereo. This happens with Bluetooth, the headphone jack and optical. It also happens with a TV that sends the sound on by ARC or eARC, unless the TV passes surround on. Connect the computer to the receiver’s HDMI input instead. How to set up surround sound covers each cable and setting.

No sound from any speaker

  1. Check that the receiver is on, and set to the input your computer uses.
  2. Make the receiver or HDMI output your default sound output.
  3. Turn up the volume on the computer and on the receiver.

Only the front speakers play

  1. On the receiver, choose a mode that keeps the computer’s channels, such as Straight, Direct or Multi Ch In. Not Stereo, and not Multi Ch Stereo or All Channel Stereo, which spread two channels over every speaker.
  2. In the receiver’s speaker setup, check that the centre and surround speakers are set to on, not None.
  3. Turn off sound effects on the computer, such as Windows Sonic, Dolby Access or a sound card’s virtual surround.

A speaker plays in the wrong place

  1. Play the receiver’s own test tone. If the same speakers are swapped there too, swap their wires at the receiver.
  2. If the receiver’s test tone is right, the computer’s setting is wrong. Don’t change the wires.
  3. Check that your computer’s setup matches your speakers. With 5.1 speakers, choose 5.1, not 7.1.
  4. On a computer with analogue jacks, plug each cable into the right colour: green for front, orange for centre and subwoofer, black for rear.

Back speakers silent on 7.1

You may have 5.1 speakers with the computer set to 7.1. Then the back channels go to speakers you don’t have. Set the computer to 5.1 and test again.

No sound from the subwoofer

  1. Raise the Test volume a step and play the subwoofer again. Its rumble starts quiet on purpose.
  2. Turn on the subwoofer. Many have their own power switch and volume knob.
  3. Check its cable, from the receiver’s subwoofer or LFE output.
  4. In the receiver’s speaker setup, set Subwoofer to Yes.

Note: The subwoofer’s low rumble is easy to miss on small speakers. Put your hand on the subwoofer: you should feel it.

To set up its cable, crossover and volume, see connect and set up a subwoofer.

How this test works

When you press Start test, your browser reports how many output channels your sound device has. The page then sends each test sound to one channel only, with no mixing. Every other channel stays silent. We check this with an automatic test that records all 8 channels inside the browser.

Each speaker plays pink noise between 500 and 4,000 Hz (hertz, vibrations per second). Receivers use the same kind of sound for their own speaker test. It has no deep bass, so the receiver can’t move it to the subwoofer. The subwoofer channel gets a low rumble between 25 and 120 Hz.

The channel order is the standard one that Windows, HDMI and most receivers use. On a Mac, Audio MIDI Setup decides which speaker gets each channel.

Your browser can’t hear your speakers. So the result comes from your answers. It tells you what your answers mean and what to try next.

See how we test sound for where our limits come from, and what a browser can’t measure.

What the test can check

  • That each speaker plays, in the right place.
  • Swapped speakers, a silent speaker and a missing subwoofer.
  • Whether your computer sends surround to the page at all.

What it can’t check

  • How loud each speaker is, in decibels, or the speaker distances.
  • Dolby Atmos height speakers, or Dolby and DTS sound formats.
  • Surround on phones, tablets and Bluetooth, which give web pages stereo only.

Questions and answers

Why does the page find only 2 channels?

Your computer gives this page stereo. Most often its speaker setup is set to Stereo. Set it to 5.1 or 7.1, as shown in If something's wrong, then press Check again.

Phones, tablets, Bluetooth speakers and most headsets always give web pages 2 channels. So do TVs that send the sound on by ARC, eARC or optical, unless the TV passes surround on. To set up the whole system, see how to set up surround sound.

Can I test Dolby Atmos?

Only the base speakers. This page checks the 5.1 or 7.1 speakers around you and the subwoofer. Atmos height speakers need Atmos content, from a film app, a game or a Blu-ray player. A web page can't send sound to them.

Most receivers have their own test tone for height speakers, in the speaker setup menu.

My gaming headset says 7.1. Can I test it?

Often not. Most "7.1" headsets are stereo headsets with software that imitates surround. The page then finds 2 channels.

Some headset apps add a virtual 7.1 device to the computer. Then the page finds 8 channels, and each speaker plays as a direction in your headset. That is a simulation, but it shows whether the software places each channel correctly.

Which order are the channels in?

The page uses the order that Windows, HDMI and most receivers use. For 7.1 that is front left, front right, centre, subwoofer, back left, back right, side left and side right. For 5.1, the last two are the surround speakers. Each speaker in the picture shows its channel number. On Linux, the order follows the sound server's speaker map.

Why does the subwoofer test sound so quiet?

The subwoofer channel plays 10 dB quieter on purpose. Receivers make that channel 10 dB louder, so the two even out. Small speakers and laptops can't play such a low rumble at all.

Does this work on a Mac?

Yes, in Chrome, Edge or Firefox, if the output is set up for 5.1 or 7.1 in Audio MIDI Setup. On a Mac, you choose which speaker gets each channel. If a speaker plays in the wrong place, check that list. Safari may give the page only 2 channels.

Why do I hear the front speakers during the surround test?

The sound for that speaker went somewhere else. Your receiver may be in a stereo or upmix mode, or the computer's setup lists fewer speakers than you have. Choose a mode on the receiver that keeps the computer's channels, such as Straight, Direct or Multi Ch In.

Guides for this test