Bass test
Find out how deep your speakers, subwoofer or headphones can play, and check that two speakers are wired the same way.
From 200 Hz down to 20 Hz
Both sidesWarning: Turn your device's volume down before you press Play. The sound starts quiet. Raise it slowly, and stop if you hear rattling or crackling: loud deep tones can damage speakers.
A deep tone slides from 200 Hz down to 20 Hz in 30 seconds. Press the button when you can't hear it any more.
Quick start
- Turn your device's volume down first.
- Press Play sweep, then raise the volume slowly.
- Press I can't hear it any more when the bass fades away.
How to read your result
Bass is the deep part of sound. Its pitch is counted in hertz (Hz): how many times the sound vibrates each second. A lower number is a deeper sound. This page plays from 200 Hz down to 20 Hz, the deepest note people can hear.
When you mark where the bass fades away, you get the lowest bass you heard. This is what it usually means:
| Lowest bass you heard | What it means | Typical for |
|---|---|---|
| 20 to 27 Hz | Very deep bass, down to the lowest notes in music | Big subwoofers, well-sealed headphones |
| 30 to 45 Hz | Deep bass | Subwoofers, large speakers, good headphones and earbuds that fit well |
| 50 to 90 Hz | Bass, but not the deepest | Bookshelf speakers, soundbars, TVs |
| 100 to 170 Hz | Little deep bass | Laptops, tablets, small Bluetooth speakers |
| Above 170 Hz | Almost no bass | Phone speakers |
Note: The answer is your speakers, your room and your ears together, at the volume you used. Ears need much more sound to hear very deep notes, so turning the volume up moves the answer lower. It is a listening check, not a lab measurement.
Rooms change bass a lot. In most rooms some deep notes boom and others almost vanish, and it changes as you move. If one step is much louder or quieter than its neighbours, move your seat or the speaker a little and listen again.
The four checks:
- Sweep: a deep tone slides from 200 Hz down to 20 Hz in 30 seconds. Press the button the moment it fades away.
- Steps: eleven fixed pitches from 200 Hz to 20 Hz. Press one, then go lower. Mark the lowest one you can still hear.
- Subwoofer: pitches from 30 to 120 Hz on both sides, like music. Check that the subwoofer plays them, and where it hands over to your speakers. Keep the volume where it is: deeper notes sound quieter to your ears even when nothing is wrong.
- Polarity: for a pair of speakers. Deep noise plays from both. Switch the right speaker between Normal and Reversed while it plays. Normal should sound fuller, with the bass between the speakers. If Reversed sounds fuller, one speaker has its two wires swapped.
If something’s wrong
No bass at all
- Press Steps, then 100 Hz. Most speakers except phones can play it.
- Check that the sound goes to the speakers or headphones you want to test.
- Raise your device’s volume a little at a time while it plays.
On iPhone or iPad, turn off Silent mode too. Phone and tablet speakers play almost no deep bass, so use headphones or other speakers.
The subwoofer stays silent
- Check that it is switched on and its light shows it is on. Many turn themselves off after a while without sound.
- Check its own volume (gain) isn’t turned right down. Halfway is a good start.
- Check the cable from your amplifier, receiver or TV to the subwoofer input (often marked LFE or Sub out).
- In an AV receiver, set the subwoofer to Yes and the main speakers to Small. Then turn the subwoofer’s own crossover knob to its highest setting, or LFE, so the receiver decides.
The surround sound test can play the subwoofer channel on its own.
Buzzing or rattling
- Turn the volume down. Speakers buzz when pushed too hard, mostly with deep tones.
- Play the Sweep quietly and note the pitch where it rattles.
- Check for loose screws, panels or objects touching the speaker or the subwoofer.
If it still rattles at a low volume, the speaker may be damaged.
One step booms, another nearly vanishes
This is usually the room, not the speaker. Deep sound bounces between the walls. Move your seat, or move the subwoofer a little away from the wall or the corner, then listen again.
The polarity check sounds the same both ways
Sit in the middle, in front of the speakers, and move them at least a metre apart. Turn off 3D, surround or spatial sound effects.
If Reversed is almost silent, your sound is mixed into one (mono) before it reaches the speakers: a single speaker box or soundbar, a Mono Audio setting, or a subwoofer that plays all the bass. Then this check can’t test the wiring.
How the bass test works
Your browser makes every sound on your device, with the Web Audio system built into it. Nothing is downloaded, and nothing is sent anywhere.
- Tones and sweep: pure sine tones, the cleanest sound for testing bass. The sweep falls by the same number of octaves each second, from 200 Hz to 20 Hz in 30 seconds. When you press during the sweep, we take the pitch from just under half a second earlier, because people press a moment after the sound has gone, and round it to 5 or 10 Hz. Bluetooth delays the sound a little too, so treat it as “about”. Use Steps to check it.
- Polarity: pink noise kept to 40–300 Hz, the same noise on both sides. Reversed turns the right side’s sound upside down. Two speakers playing opposite sounds cancel their bass, so the reversed sound is thinner when the wiring is right.
- Level: every sound plays at about the same average level, fades in over one second and starts at 30% volume. Press Stop, or the Esc key on a keyboard, to stop: the sound fades out gently, so a subwoofer doesn’t thump. A steady tone or noise stops by itself after 5 minutes, to protect your speakers.
- Limits: we can’t measure how loud the sound is in your room or hear it ourselves. Hearing is far less sensitive to deep notes: at 20 Hz, a tone must be about 76 dB stronger than at 1,000 Hz to be heard at all (ISO 226). This page is not calibrated, and it is not a hearing test.
Questions and answers
Why can't I hear anything on my phone or laptop?
Small speakers can't move enough air for deep bass. Phone speakers play almost none: the sound fades out well above 100 Hz. Most laptop speakers fade out somewhere between about 100 and 200 Hz.
That is normal, not a fault. Plug in headphones or bigger speakers to test bass.
Why can't I hear 20 Hz, even with a subwoofer?
Your ears are far less sensitive to very deep notes. A 20 Hz tone has to be very much louder than a middle tone before you hear it at all, so at a safe volume you may only feel it, or notice nothing.
Many home subwoofers also fade out between 20 and 30 Hz. Hearing bass down to 30 to 40 Hz is already very good. For the whole range people hear, see human hearing range.
Is it safe for my speakers and my ears?
Yes, at a sensible volume. The sound starts quiet and fades in over a second. Set a comfortable level at 100 Hz, and don't turn it up for the deeper steps.
Stop at once if you hear rattling, crackling or a hard knocking. That is the speaker reaching its limit, and loud deep tones can damage it. Don't play deep tones loudly for a long time.
Why test tones and not a bass-heavy song?
A song mixes many notes, so you can't tell which pitch your speakers drop, or which one makes something rattle. A single tone, or a slow sweep, shows exactly where the bass stops and where problems start. Use a song afterwards to judge whether you like the sound.
What is a subwoofer crossover?
It is the pitch where the subwoofer hands the bass over to your main speakers. 80 Hz is a common setting for home cinema.
If the bass is too thin, too boomy, or one step in the Subwoofer check is missing, check the crossover. With an AV receiver, set it in the receiver (main speakers to Small, often 80 Hz) and turn the subwoofer's own crossover knob to its highest setting, or LFE. With a plain stereo amplifier, use the knob on the subwoofer. Step by step: connect and set up a subwoofer.
Can I check polarity with headphones?
Not with this check. With speakers, a reversed speaker cancels the bass between them. Headphones play straight into each ear, so you don't hear that. The Headphone test on this site has its own polarity check, which listens for where the sound sits in your head.
Which speaker is reversed?
The check can't tell, because it compares the two speakers. Either one will do the job if you swap its two wires. To find the one that is wrong, check the + and − markings on each cable end. On a passive speaker you can also use a 1.5 V battery: turn the amplifier off and unplug the speaker's cable from it first. Then touch the battery to the cable for a moment. The cone should move outwards when the + wire meets the + end.
Can I use it in a car?
Yes, if your phone plays through the car's speakers by Bluetooth or a cable. Bluetooth is fine for this. Start with the car's volume low, and listen for rattles in the doors and panels during the sweep.
Does it break in new speakers?
No. This page plays short test sounds. Most speakers don't need a "break-in", and playing deep tones for hours is more likely to wear a speaker than help it.