Short answer

A restart turns the router or modem off and on and keeps your settings. Try it first: unplug the modem and router and wait a minute. Plug in the modem, then the router two minutes later. A factory reset erases everything. Hold the small Reset button with a paperclip while the box is on, for your brand’s time below.

Jump to your brand: Arris · Spectrum · TP-Link · Cisco · Ubee · Sagemcom · Cox Panoramic Wifi · MikroTik · eero

  1. Reset hole: press the button inside with a straightened paperclip while the router is on.
  2. Power socket: unplug here for a restart.
  3. Power button, on some models: off and on is also a restart.
  4. Internet (WAN) port: the cable from the modem or wall. Leave it in.

The reset button sits in a small hole so you can't press it by accident. Some routers have it underneath or on the side.

Restart first (works for every brand)

A restart fixes many slow or dropped connections and erases nothing.

  1. Unplug the power cable from the modem.
  2. Unplug the power cable from the router. Skip this if one box does both (a “gateway”).
  3. Wait at least 30 seconds. Spectrum asks for a full minute.
  4. Plug the modem back in and wait until its internet or Online light is steady.
  5. Plug the router back in and wait another two minutes.

Spectrum and Cox also let you restart their equipment from their app or website (see below). If the connection still drops, work through Wi-Fi keeps disconnecting before you reset anything.

Factory reset: what you lose

Restart

Keeps everything

Unplug it or press Reboot in its app. Fixes a stuck router. Your Wi-Fi name, password and settings stay.

Factory reset

Erases everything

Hold Reset. Use it when you forgot the admin password, give the router away, or a restart didn’t help.

A factory reset erases:

  • your Wi-Fi name and password (they go back to the ones on the label)
  • the router’s admin password
  • every setting you changed: parental controls, port forwarding, reserved addresses

Every device drops off the Wi-Fi until you connect it again.

Reset button by brand

Press the button while the device is on, unless the brand’s section says otherwise. A short press often only restarts it.

Brand Where the button is, and how long to hold it
Arris SURFboard Back (bottom on the S33 and S34). 10 s on the SB8200, 20 s on the S33 and S34.
Spectrum router Back or side, by model. More than 15 s (4–14 s only restarts it).
TP-Link Back: Reset or WPS/Reset. More than 10 s, until the SYS light flashes fast.
Cisco RV160 / RV260 Back. More than 10 s (3–10 s only restarts it).
Linksys Back or bottom. About 10 s.
Ubee Back. More than 10 s.
Sagemcom F@st 5260 Left side. 15 s or more, until the power light goes off.
Cox Panoramic Wifi Back, recessed. More than 10 s, until the front light flashes.
MikroTik Varies. Hold while you plug in the power; let go when a light flashes.
eero Bottom on most models. About 15 s, until the light flashes red (not Ring Alarm Pro: see eero).

How to reset an Arris modem or router

Arris modems and Wi-Fi gateways are sold under the SURFboard name.

Restart: unplug the power cable, wait 30 seconds and plug it back in. Give it a few minutes to connect.

  1. Leave the modem switched on.
  2. Find the Reset hole on the back. On the S33 and S34 it is on the bottom.
  3. Press the button inside with a paperclip. You should feel a click.
  4. Hold it for 10 seconds on the SB8200, or 20 seconds on the S33 and S34. The model name is on the label.
  5. Let go. The front lights flash, and the modem can take 5 to 30 minutes to connect again.

S33 and S34 from the web page: on a computer connected to the modem, go to 192.168.100.1 and log in. On the Configuration page, click Restore Factory Defaults. For the SB8200, Arris gives only the button.

How to reset a Spectrum router or modem

My Spectrum app

  1. Open the My Spectrum app and sign in.
  2. Tap Services, then your modem or router.
  3. Tap Restart Equipment.

Spectrum.net

Sign in at spectrum.net, go to Services Internet, choose your equipment and select Restart Equipment. Some equipment, and modems you bought yourself, can only be restarted by unplugging them.

Unplug it

Unplug the modem’s power cord, wait at least one minute and plug it back in. Wait until its lights are steady, then plug in the router. Fiber customers: leave the back of the fiber modem alone.

Factory reset a Spectrum router:

  1. Leave the router on.
  2. Find the Reset button: on the side of the Spectrum WiFi 6 router, on the back of the WiFi 6E router.
  3. Hold it for more than 15 seconds. Holding it for 4 to 14 seconds only restarts the router.
  4. When it has started up, set a new Wi-Fi name and password.

In the app, the reset is under Services Advanced Settings Factory Reset, then Delete Network Settings.

Restart (keeps your settings):

  1. Press the Power button on the back, or unplug the router. Not every model has a button.
  2. Wait 30 seconds, then switch it on again.
  3. Or, on a device on your Wi-Fi, go to tplinkwifi.net, log in and open Advanced System Tools Reboot (on newer models Advanced System Reboot).

The Tether app can restart it too. TP-Link Deco mesh units are managed in the Deco app instead.

Factory reset:

  1. Leave the router on.
  2. Find the Reset or WPS/Reset button on the back. On a WPS/Reset button, a press under 5 seconds only starts WPS.
  3. Hold it for more than 10 seconds.
  4. Let go when the SYS light changes from slow to fast flashing.
  5. Keep the router plugged in while it restarts.

From the web page, it is Advanced System Tools (or System) Backup and Restore Factory Default Restore. In the Tether app: Tools System Factory Default Restore. Some models, such as TP-Link 4G routers with a recessed button, use other times: check your model on tp-link.com.

How to reset a Cisco router

“Cisco router” can mean three different things.

Old Cisco Linksys

E-series, WRT

With the router on, hold Reset for about 10 seconds. Linksys now supports these models on its own site.

Cisco RV small business

RV160, RV260

Hold Reset for more than 10 seconds (3 to 10 seconds only restarts it).

Cisco IOS business router

No reset button

A job for whoever manages the network: it needs a console cable (see below).

Cisco RV160 and RV260:

  1. Leave the router on.
  2. Press Reset with a paperclip or pen tip and hold it for more than 10 seconds.
  3. Wait a few minutes for it to start up.
  4. Open https://192.168.1.1. The user name and password are both cisco: change the password the first time you log in.

You can also reset from its web page: Administration Reboot, choose Return to factory default settings after reboot and click Reboot. Older RV models use other times, so check your model on cisco.com.

Cisco IOS routers without a reset button: connect a console cable. Type enable, then write erase, confirm, and type reload. Answer no if it asks to save. This erases the whole saved setup and cuts remote access, so keep a copy of the configuration first.

How to reset a Ubee router

Ubee modems and gateways usually come from an internet company.

  1. Leave the Ubee on.
  2. Find the small Reset hole on the back.
  3. Press the button inside with a paperclip and hold it for more than 10 seconds.
  4. Let go. The lights blink while it restarts; wait until they are steady.

If your settings are still there afterwards, it only restarted: hold the button longer. Ubee notes that not every setting goes back to default on some models. Your provider’s app may also restart it remotely.

How to reset a Sagemcom router

Sagemcom routers also usually come from an internet company. Spectrum uses the F@st 5260.

  1. Leave the router on.
  2. Find the Reset button. On the F@st 5260 it is on the left side panel.
  3. Hold it for 15 seconds or more. The Power light turns off to show the reset has started.
  4. Let go. The router restarts with its factory settings, which takes a few minutes.

A short press only restarts it. Other Sagemcom models may use other times: check the guide for yours. On the F@st 5260 a solid red power light means a firmware update is running, so don’t unplug it then.

How to reset a Panoramic Wifi router (Cox)

Restart in the Panoramic Wifi app:

  1. Open the Panoramic Wifi app and go to the Overview tab.
  2. Scroll to Connection Trouble?
  3. Tap Restart Gateway. It can take up to 12 minutes, without internet in the meantime.

On a computer, sign in to My Account on cox.com, select Refresh Modem on your Internet service, then Start Troubleshooting. Or unplug the power cord from the back of the gateway, wait 30 seconds and plug it back in.

Factory reset with the button:

  1. Leave the gateway on.
  2. Find the recessed Reset button on the back.
  3. Hold it with a paperclip for more than 10 seconds, until the front light flashes.
  4. Let go and wait for it to come back online.

The Wi-Fi name and password go back to the ones on the gateway’s label. You can change them in the Panoramic Wifi app. Some newer white gateways have no reset hole: ask Cox how to reset yours.

How to reset a MikroTik router

MikroTik’s reset button works while the router starts up.

  1. Unplug the power cable.
  2. Press and hold the Reset button, and keep holding it while you plug the power back in.
  3. Let go as soon as a light (usually USR) starts flashing, after about 5 seconds.

Don’t keep holding: the button does other things the longer you hold it.

Hold, while it starts The light What happens
About 5 s Starts flashing Resets the settings. This is the one you want.
About 10 s Stays on CAP mode: it waits to be managed by another MikroTik router.
About 15 s Goes off Netinstall: for reinstalling RouterOS from a computer.

Can you still log in? Then reset without the button: in WinBox or the web page go to System Reset Configuration, or type /system reset-configuration in the terminal.

After the reset, open 192.168.88.1 on most models. The user name is admin. Newer devices have the password on the sticker; older ones have none, so set one straight away.

How to reset an eero router

eero has two button resets. For a soft reset, which keeps your network, let go when the light flashes yellow (by 8 seconds). Hold it about 15 seconds, until the light flashes red, for a hard reset, which erases it. Our guide on how to reset an eero router has both resets and the app steps.

After the reset

  1. Wait until the lights are steady.
  2. Join the Wi-Fi name on the label, with the password on the label. Mesh systems such as eero are set up in their app instead. For a modem without Wi-Fi, use an Ethernet cable.
  3. Log in to the router’s app or web page with the details on the label.
  4. Set a new Wi-Fi password, and a new admin password if the label has a common one such as “admin”.
  5. Connect your devices again.

Test it now

Internet speed test

It shows whether the connection works again and what speed reaches this device. What is a good internet speed? tells you if the number is enough.

Run the speed test

Questions people ask

Will resetting my router make the internet faster?

Not on its own. A restart clears a stuck router and often fixes drops and slowdowns, but it can’t raise your plan’s speed. A factory reset rarely helps more than a restart. For lag in games, see why your ping is high.

What is the 30-30-30 reset?

An old method: hold reset for 30 seconds with the router on, 30 unplugged, then 30 plugged in again. Current routers don’t need it. Use the time for your brand above.

Why didn't my reset work?

The router was probably off, or the button wasn’t held long enough. Check that the power light is on, press until you feel a click and hold for the full time. If it still won’t reset, contact the maker or your internet company.