Microphone quality test

Find out how good your microphone sounds, and why.

Your voice stays on your device. We don't upload or keep it.

Your browser will ask to use your microphone. Choose Allow.

Quick start

  1. Press Start quality test, then choose Allow.
  2. Stay quiet for 3 seconds while we measure the background.
  3. Read the sentence out loud. Your result appears when you finish.

How to read your results

Your result starts with one sentence about how your microphone sounds. Under it are the numbers it is based on. Levels are in dBFS: decibels below the loudest sound your microphone can record. So −60 dBFS is much quieter than −20 dBFS.

What you see What it means
Background noise The sound while you were quiet: hiss, fans, traffic. Below −60 dBFS is low. From −45 dBFS it is loud.
Your voice How loud your voice reached the microphone. From −30 to −8 dBFS is a good level.
Voice above the noise How much louder your voice was than the background. 30 dB or more is good, 40 dB or more is excellent. Under 20 dB, people struggle to follow you.
Voice reaches The highest pitch where your voice stands out. Past 10,000 Hz sounds full and crisp. Around 4,000 Hz sounds like a phone call. We only show it when your voice was clear and long enough to tell.
Loudest moment The highest peak. If it hits the top (the limit), your voice distorts.
No hum We listen for a steady 50 or 60 Hz hum from mains power while you are quiet.

Your voice by pitch draws your voice as a filled curve and the background as a dashed line. Low sounds are on the left, high sounds on the right. The bigger the gap between them, the clearer you sound.

Browser clean-up shows what your browser did to the sound: echo cancellation, noise suppression and automatic volume. Not reported means the browser doesn’t say.

Compare two takes: record a second take with another microphone, with the browser clean-up on, or after you fix something. The test says which take sounds better and why. Play both and listen.

Tip: Sit as you would in a call. Speak at your normal volume, not louder.

Recording two people, such as a family story? Test both voices first: see how to record a family story.

If something’s wrong

These are the most common problems, most likely first.

Your voice crackles or sounds harsh

Your voice is too loud for the microphone, so the peaks are cut off. This is called clipping.

  1. Move back a little from the microphone.
  2. Lower the microphone’s input volume in the system settings.
  3. Turn off “microphone boost” if your sound settings have it.

Windows

  • Open Settings, then System, then Sound.
  • Under Input, choose your microphone and lower its Volume.

Mac

  • Open System Settings, then Sound, then Input.
  • Choose your microphone and move Input volume down.

Others hear hiss or room noise

The background is too loud compared with your voice.

  1. Turn off fans, music and the TV, or move to a quieter room.
  2. Move closer to the microphone, then lower its volume a little. Your voice then stands out more.
  3. Try a headset microphone near your mouth.
  4. Compare a take with the browser clean-up on. It lowers steady noise.

For the room, the light and the microphone distance on video calls, see how to look and sound better on video calls.

Your voice is very quiet

  1. Move closer to the microphone.
  2. Raise the input volume in the system settings above.
  3. Check that nothing covers the microphone, such as a case or your hand.

Still too quiet? See your voice is too quiet for more fixes.

You sound like a phone call, or muffled

High sounds such as “s” and “f” don’t come through.

  1. Bluetooth headphones switch to a call mode when their microphone is on. Use a wired or USB headset, or your computer’s microphone. Here’s how to keep stereo sound on calls.
  2. Point the microphone at your mouth. Many microphones hear best from the front.
  3. Take off anything that covers it, such as a foam cover that is too thick, or a scarf.

There is a hum

A steady low hum usually comes from power.

  1. Unplug the laptop charger for a moment and test again.
  2. Plug the microphone into another USB port, or use a different cable.
  3. Keep the microphone cable away from power cables and adapters.
  4. A fan, a fridge or an air conditioner can hum too. Switch it off for a moment and test again.

Your microphone is blocked

The browser asked to use your microphone, and the answer was no, or a setting blocks it. The test shows the steps for your browser. In short:

  1. Click the lock or settings icon next to the address bar.
  2. Set Microphone to Allow.
  3. Press Try again.

“We couldn’t tell your voice apart from the background”

The microphone sends sound, but nothing in step 2 was clearly louder than the background. Stay quiet in step 1, and speak only in step 2. If you speak in step 1, the test takes your voice for the background, and says “We heard sound while the test needed quiet”. If it still happens, the test may listen to another microphone: choose yours under Compare two takes, or check it with the microphone test.

Problems on iPhone or iPad

  1. Hold the phone about a hand’s width from your mouth, with its microphone uncovered.
  2. End any phone or video call. Other apps can hold on to the microphone.
  3. If you can’t hear a take, check that Silent mode is off.

How this test works

When you press Start quality test, your browser asks to use your microphone. We ask for it with the browser’s clean-up off, so we hear the microphone itself. The sound is measured inside your browser, many times a second, and is never sent to us.

Step 1 measures the background for 3 seconds: its level (the middle value of the readings), its sound by pitch, and any steady hum at 50 or 60 Hz (mains power) and their multiples. Step 2 measures your voice while you read the sentence. A moment counts as voice when it is at least 10 dB above the background. Your voice level is the 95th percentile of those moments, so the loud parts of words count, not the pauses. Step 2 ends by itself after about 2.5 seconds of voice and a short pause, or after a longer pause when you read only a few words.

How high your voice reaches is the highest third of an octave where your voice is at least 10 dB above the background. The sentence has many “s” sounds, so a good microphone shows its full range.

See how we test microphones for where our limits come from, and what a browser can’t measure.

What the test can check

  • Background noise, voice level and how clearly the voice stands out, in dBFS and dB.
  • Clipping (a voice too loud for the microphone), a steady hum, and a voice that sounds like a phone call or dull.
  • What your browser’s clean-up did, and how two takes compare.

What it can’t check

  • The loudness of your room. dBFS is relative to the microphone, not calibrated sound.
  • Exactly how a call app will sound: each app has its own processing.
  • Every kind of distortion. A crackle below the limit, or a loose cable, can still sound bad: listen to your take.
  • Fine details of the sound that only your ears can judge. Play your takes back and listen.

The numbers are estimates and the limits are rules of thumb for speech. A voice, a microphone and a room all differ, so trust your ears as well.

Questions and answers

What is the difference with the microphone test?

The microphone test answers "Does my microphone work?" It checks that sound gets through, quickly.

This quality test answers "How good does it sound, and why does it sound bad?" It measures the background noise, how clearly your voice stands out, distortion, hum and how high your voice reaches. It also compares two microphones.

Is my voice recorded or uploaded?

No upload, ever. The test measures the sound inside your browser, on your device.

Each take is recorded so you can play it back. The recording is kept in this browser tab only, and it is gone when you leave the page.

What does "browser clean-up" mean?

Browsers can clean up microphone sound before a website gets it, as call apps do. They cancel echo, lower steady noise and even out the volume. The test first measures your microphone with this clean-up off, so you hear the microphone itself. Under Compare two takes, you can record it again with the clean-up on. The clean-up is made for speech, so it can make music worse: see music sounds bad on calls.

Can it tell me the noise level of my room in decibels?

No. A browser only gets numbers relative to the loudest sound your microphone can record (dBFS). How loud that is in the room depends on the microphone and its volume setting. A sound level meter needs a calibrated microphone.

Why does my Bluetooth headset sound like a phone?

When their microphone is on, most Bluetooth headphones switch to a call mode. It sends sound at a low quality, without the high sounds. The test shows this as "Like a phone call". A wired or USB headset, or the computer's own microphone, usually sounds better. See Bluetooth headphones sound bad on calls.

Why do I sound different in Zoom, Teams or Discord?

Each app has its own clean-up, and its own microphone setting. Compare a take with the browser clean-up on to hear roughly what a call app does. Then check which microphone the app uses.

Guides for this test