Headphone test

Check your headphones or earbuds, one ear and one sound at a time.

Put your headphones on, with L on your left ear. Turn off spatial audio, and turn the volume down to about a quarter.

Quick start

  1. Put your headphones on and turn the volume down.
  2. Press Start headphone test, then Play left.
  3. Choose where you heard it, then press Next check.
  4. After the last check, press Show my result.

How to read your results

Each check plays a sound. Then you choose what you heard. The ear cup that plays turns orange in the picture.

Check What a good result sounds like If it doesn’t
Left and right The left sound in your left ear, the right sound in your right ear. One side silent, swapped, or both ears every time (mono).
Centre The sound sits in the middle of your head. It leans to one side: the balance is off, or one side is weaker.
Polarity One sound sits in the middle. The other sounds spread out. The wrong one sits in the middle: one side is wired the wrong way round.
Bass to treble A smooth tone from deep bass to high treble. Crackling, buzzing, or one side going quiet.
Bass rattle A smooth, deep hum. Rattling or buzzing: loose parts or a damaged speaker.
Earbud fit The bass stays about the same when you press an earbud in. The bass gets much louder: the earbud may not seal your ear.

Your result then says in words what you found, such as “Left and right are swapped.” It also lists what to do next.

Left and right decide the result. The other checks are optional, and each one can add a finding.

Tip: Two polarity sounds that seem the same are common. That doesn’t count as a problem. If one of your ears hears less than the other, the Centre check may lean that way. That is your hearing, not a fault in the headphones.

If something’s wrong

These are the most common problems, most likely first.

No sound at all

  1. Turn up the volume, and check that your device isn’t muted.
  2. Check that the sound goes to your headphones, not to other speakers. If the test shows a Play through list, choose your headphones there.
  3. Bluetooth: check that the headphones are connected and charged.
  4. Press Play left again.

Windows

  • Click the speaker icon on the taskbar.
  • Choose your headphones in the list.

Mac

  • Open Control Center, then Sound.
  • Choose your headphones.

Sound in one ear only

  1. Push the plug in all the way. Turn it a little while the sound plays.
  2. Set the balance to the middle. See The sound leans to one side.
  3. Try the headphones on another phone or computer. If one side is still silent, the headphones are faulty.

Bluetooth headphones or earbuds? Try the steps in the next row too. For every fix by brand, see one AirPod or earbud not working.

Tip: Does this test play in both ears, but your music doesn’t? Then the song or video may be the reason. Some old recordings put a sound on one side only. Try another song.

One Bluetooth earbud or side doesn’t play

  1. Charge both sides. Put both earbuds in the case for 30 seconds. Check on your phone that each one charges. Each earbud has its own battery.
  2. Restart them. Put both earbuds in the case, close the lid and wait 30 seconds. Then take them out again. Headphones: turn them off and on.
  3. Pair them again. Open the Bluetooth settings on your phone or computer. Choose Forget (or Remove) for your headphones. Then connect them again. Still failing on Android? Reset Bluetooth on the phone.
  4. Reset them. See below for AirPods. For Galaxy Buds, see our reset guide. For other earbuds, see the maker’s manual or app. Then pair them again.
  5. Update them. Install any update in the maker’s app. AirPods update by themselves while they charge near your iPhone.
  6. Try the cable. Some headphones have a cable socket. If both sides play with the cable, the Bluetooth part is faulty.
  7. Try another phone or computer. If the same side is still silent, contact the maker or a repair shop. Ask about the warranty.

To reset AirPods, put them in the case, close the lid and wait 30 seconds. On your iPhone, open Settings, then Bluetooth. Tap the i next to your AirPods, then Forget This Device. Open the lid, then:

Your AirPods What to do
AirPods 1 to 3, AirPods Pro 1 and 2 Hold the button on the back of the case for about 15 seconds, until the light flashes amber (orange), then white.
AirPods 4, AirPods 5, AirPods Pro 3 (all models) The case has no button. Double-tap the front of the case while the light is on. Double-tap again when it flashes white, and a third time when it flashes faster. Wait until it flashes amber, then white.

If the light doesn’t flash white, close the lid for 20 seconds and try again. To see what each light on the case means, see what the AirPods lights mean. Then hold the open case near your iPhone, and follow the steps on the screen.

Left and right are swapped

  1. Check the L and R marks on your headphones. Wear them on the matching ears.
  2. Turn off any setting that swaps the sides, in your sound app or headphone app.

Both ears play the same sound

Turn off Mono audio, and sound effects such as spatial audio:

Windows

  • Open Settings, then Accessibility, then Audio.
  • Turn off Mono audio.

Mac

  • Open System Settings, then Accessibility, then Audio.
  • Turn off Play stereo audio as mono.

On iPhone and iPad, open Settings, then Accessibility, then Audio and Visual. On Android, open Settings, then Accessibility. Look for Audio adjustment, or Hearing enhancements on Samsung phones.

The sound leans to one side

The balance setting sends more sound to one ear. Set it to the middle:

Device Where to find the balance
iPhone and iPad Open Settings, then Accessibility, then Audio and Visual. Drag Balance to the middle.
Android Open Settings, then Accessibility, then Audio adjustment. Drag Audio balance to the middle. On Samsung phones, it’s in Hearing enhancements, called Left/right sound balance.
Windows 11 Open Settings, then System, then Sound. Choose your headphones. Set Left channel and Right channel to the same number. If you don’t see them, open Volume.
Windows 10 Open Settings, then System, then Sound. Choose Device properties, then set Balance left and right to the same number.
Mac Open System Settings, then Sound. Choose your headphones under Output. Drag Balance to the middle.

Then press Play both in the Centre check again. The sound should sit in the middle.

Some headphone apps and sound apps have their own balance or sound effects. Check them too.

Note: Hearing settings can make one ear louder on purpose, to suit your hearing. One example is Headphone Accommodations on iPhone. If you set one up, that’s why.

One side is quieter

  1. Clean the mesh on your earbuds. Earwax can make one side quieter. Take off the ear tips, then brush the mesh gently with a soft, dry brush. Don’t use anything sharp, and don’t hold them under water.
  2. Set the balance to the middle. See The sound leans to one side.
  3. Check that both ear tips fit. A loose one loses sound, mostly bass.
  4. Headphones over your ears: turn them round, with L on your right ear. Play the sound again. If the quiet side moves to the other ear, the headphones cause it. If it stays, it may be your hearing.

Crackling, buzzing or rattling

  1. Lower the volume and play the sound again. Many headphones rattle only when loud.
  2. Check the ear cups and ear tips for loose parts, dirt or hair.
  3. Check the cable and the plug. Bluetooth: move closer to your device, and charge the headphones.

If one side rattles at a low volume, its speaker may be damaged.

Weak bass on earbuds

  1. Run the Earbud fit check.
  2. Try another ear tip size. Many earbuds come with three, and each ear may need a different size.
  3. Put each earbud in with a small twist, so it seals your ear. Never force it.

Open earbuds without soft tips, such as standard AirPods, don’t seal, so they play less bass by design.

Some earbud apps have their own fit test, such as the Ear Tip Fit Test for AirPods Pro.

No sound on iPhone or iPad

  1. Turn off Silent mode. On most iPhones, it’s the switch on the side. On others, it’s the Action button or Control Center.
  2. Turn the volume up with the side buttons.

Note: An iPhone call, Siri or locking the screen pauses the sound. Press a play button again to go on.

How this test works

When you press a play button, your browser makes the sound itself. There is no sound file to download.

Check The sound
Left and right, Centre Three soft notes, like a doorbell, played three times.
Polarity The same soft hissing sound (pink noise) twice, on both sides. In one of them, the right side is upside down. Which one changes each visit.
Bass to treble One tone that rises from 20 Hz (hertz, vibrations per second) to 20,000 Hz in 20 seconds.
Bass rattle One tone that rises from 20 Hz to 200 Hz in 15 seconds.
Earbud fit A soft 60 Hz hum for 12 seconds.

Every sound is about as loud as the chime, and fades in, so no check is suddenly louder than the one before. The test sends each sound only to the side it names. The other side gets silence. We check this with an automatic test that records the sound inside the browser.

Your browser can’t hear your headphones. So the result comes from your answers. It tells you what your answers mean and what to try next.

See how we test sound for where our limits come from, and what a browser can’t measure.

What the test can check

  • That each ear plays, on the correct side.
  • Balance, polarity, crackling and rattling, as you hear them.
  • Whether your earbuds seal your ears.

What it can’t check

  • How loud your headphones are, in decibels.
  • Their exact frequency range, or your hearing.
  • Sound delay on Bluetooth headphones.

Questions and answers

How is this different from the sound test?

The sound test is a quick left and right check for any speakers or headphones.

This headphone test goes further, for headphones and earbuds. It also checks the centre, polarity, bass rattle and earbud fit.

Can I test AirPods and other Bluetooth earbuds?

Yes. Connect them first, then press Start headphone test. The sound may start a moment late. That is normal for Bluetooth.

Turn off spatial audio and head tracking first. They move the sound around, so left and right are hard to judge.

Can I choose which headphones to test?

Yes, in most browsers on a computer. Choose them in the Play through list under the volume. Firefox shows a Choose headphones button instead. The other sound tools in this tab use the same choice.

Chrome, Edge and Safari on a Mac show the list only while this site may use your microphone. iPhones, iPads and Android phones always use the system's sound output. Then choose the headphones in your device's sound settings, as shown under No sound at all above.

Is the test safe for my ears?

The test starts at a low volume, and every sound fades in. Turn your device's volume down before you start, and raise it only if a sound is too quiet. Don't turn it up to hear the lowest or highest notes of the sweep.

What does polarity mean?

Each speaker moves in and out to make sound. Both sides should move in at the same time.

If one side is wired the wrong way round, it moves out while the other moves in. The sound then seems spread out instead of sitting in the middle of your head. Sound effects such as spatial audio can do the same, so turn them off first.

Why do I hear the left sound in both ears?

Your device plays mono sound. The Mono audio setting may be on, in the Accessibility settings. Sound effects such as spatial audio or virtual surround also mix the sides. Turn them off and test again.

Why does my music stop when I press Play on iPhone?

On iPhone and iPad the test plays its sound like a video, so you hear it even in Silent mode. Like a video, it pauses music from other apps. Start your music again when you are done.

Can this test break in new headphones?

No. This test plays short sounds to check your headphones. It doesn't play the hours of sound that burn-in would take.

Is this a hearing test?

No. It checks your headphones and earbuds. If you think your hearing has changed, see a doctor or a hearing specialist.

Guides for this test